NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 51

NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 12

NXP Semiconductors

UM11723

KITPF5200FRDMEVM evaluation board

4. Disconnect and reconnect the USB cable into the SDA port.

•

This time without pressing the RST push-button, the FRDM_KL25Z device should

appear on the left pane of the File explorer as shown in the following figure.

•

5. Locate the file

nxp-gui-fw-frdmkl25z-usb_hid-pf5200_v0.8.bin

from the package

and drag and drop the file into the FRDM_KL25Z device.

•

Note: Make sure to allow enough time for the firmware to be saved.

6. Freedom board firmware is successfully loaded. Disconnect the USB cable from the

SDA port and reconnect it into the KL25Z USB port.

5.2 PF52 NXP GUI

5.2.1 Installing the GUI software package

To install the PF5200 NXP GUI download or obtain the NXP GUI package, unzip an open

1-NXP_GUI_Setup folder:
1. Download or obtain the NXP GUI package. Unzip and open the 1-NXP_GUI_Setup

folder.

2. Double-click

NXP_GUI_version-Setup.exe

and follow the instructions.

UM11723

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 1 — 8 December 2021

12 / 51

«
...
10
11
12
13
14
...
»

Содержание KITPF5200FRDMEVM




















































Отзывы:

Нет отзывов