manualshive.com logo in svg

NXP Semiconductors KITPF5200FRDMEVM, Руководство пользователя, Страница: 10 / 51

Поделиться
Скачать
NXP Semiconductors KITPF5200FRDMEVM Скачать руководство пользователя страница 10

NXP Semiconductors

UM11723

KITPF5200FRDMEVM evaluation board

aaa-044591

GND

TP15

TP13

VIN

VIN

V1P5D

SW1OUT

TP11

TBBEN

GND

TP16

GND

TP17

GND

TP18

GND

TP19

GND

GND

GND

GND

GND

TP9

I2C_SDA

TP7

I2C_SCL

TP5

SYNC

TP3

TP1

TP14

VDDIO

VDDIO

SW2OUT

TP12

VDDOTP

TP10

XFAILB

TP8

RESETBMCU

TP6

PWRON

PGOOD

TP4

TP2

Figure 3. Test points

4.4 Schematic, board layout and bill of materials

The schematic, board layout and bill of materials for the KITPF5200FRDMEVM

evaluation board are available at 

http://www.nxp.com/KITPF5200FRDMEVM

.

5 Installing and configuring software and tools

5.1 Flashing or updating the GUI firmware

The KITPF5200FRDMEVM is delivered with the GUI firmware already flashed. If your

MCU firmware is already flashed, you can ignore this section. If you need to update the

firmware or it is malfunctioning, follow the instructions detailed in the following sections.

5.1.1 Flashing the FRDM-KL25Z firmware – Windows 7

If BOOTLOADER is already loaded on the FRDM-KL25Z board, skip Step 1 and Step 2

and start with Step 3.
1. Press the RST push-button and plug the USB cable into the SDA port on the FRDM-

KL25Z board.

•

A new “BOOTLOADER” device appears on the left pane of the File explorer.

2. Locate the file 

MSD-DEBUG-FRDM-KL25Z_Pemicro_v118.SDA

 from the package

and drag and drop into the BOOLTLOADER device.

•

Note: Make sure to allow enough time for the firmware to be saved in the

bootloader.

UM11723

All information provided in this document is subject to legal disclaimers.

© NXP B.V. 2021. All rights reserved.

User manual

Rev. 1 — 8 December 2021

10 / 51

Содержание KITPF5200FRDMEVM




















































Отзывы:

Нет отзывов