Nuna tres lx, Руководство пользователя

Страница: 11 / 25

7
TRES lx instructions
TRES lx instructions
EN EN
8
Product Set Up
Installation Concerns
DO NOT install this enhanced child restraint on vehicle seats with lap belts only. (1)
This enhanced child restraint is suitable for vehicle seats with a 3-point retractor safety belt. (2) If your vehicle
has ISOFIX anchor points, we recommend that you connect the ISO Connector™ attachment to the ISOFIX
anchor points (Forward Facing Mode). (3)
DO NOT use the rearward facing system on the passenger seat with activated frontal airbag. (4) Death or serious
injury may occur. Please reference vehicle owner’s manual for more information.
DO NOT install this enhanced child restraint on vehicle seats that face sideways or rearward with respect to the
moving direction of the vehicle.
Please refer to your vehicle owner’s manual for recommended or suggested installation positions.
This enhanced child restraint must be installed in the rear vehicle seat.
(4)
DO NOT install this on movable vehicle seats during installation.
Product Use
Use Side Impact Shield
1
- The enhanced child restraint is delivered with detachable side impact shield. This side impact shield must be
used on the door side of the vehicle for best protection. It must be connected on the outside of the enhanced
child restraint. Installation shown in fig (5) .
2
- Press the release button to remove side impact shield. (6)
Recline Adjustment
1
- Press the recline adjustment handle, and adjust the enhanced child restraint to the proper position. (7)
2
- The recline angles are shown as (8).
There are two recline angles 5-6 for rearward facing mode.
There are four recline angles 1-4 for forward facing mode.
Align the top reclining indicator with the bottom numbers for the desired recline position.
Height Adjustment for Head Support and Shoulder Harnesses
Please adjust the head support and shoulder harnesses to proper height according to the child's height.
When used in rearward facing mode, the shoulder harness slots must be even with or just below the child’s
shoulders. (9)-1
If the shoulder harnesses are not at proper height, the child may be thrown from the enhanced child restraint
in case of an accident.
When used in forward facing mode, the shoulder belt guides must be even with or just above the child’s
shoulders. (9)-2
Squeeze the head support adjustment lever (10)-1 , meanwhile pull up or push down the head support until it
clicks into one of the 10 positions.
The head support positions are shown as
(10)-2 .
As the headrest is adjusted up (from 6th-9th position), the sides of the child restraint automatically move
outward to provide more shoulder room.
Rearward Facing Mode
(Child height 40cm-105cm/ Child weight ≤ 22kg)
Please install the enhanced child restraint on the rear vehicle seat, and then put the child in the enhanced
child restraint.
Installation for Rearward Facing Mode
Please adjust the enhanced child restraint to the desired recline position (2 positions for rearward facing
mode). Align the top reclining indicator with one of the bottom white numbers.
Make sure the shoulder harness is adjusted to proper height before installing this enhanced child restraint.
When installing and adjusting the safety belts, make sure that both the shoulder belt and the lap belt are not
twisted and will not stop the safety belts from functioning properly.
1
- Pass the vehicle lap belt through the vehicle lap belt slots, then engage the vehicle buckle tongue into the
buckle. (11)(12)
Vehicle lap belt must pass underneath infant insert.
2
- Pass the vehicle shoulder belt through the two rear-facing vehicle belt slots at the back of the enhanced child
restraint.
(13)
Open the belt lock off and insert the shoulder belt through it. (14)
Ensure the belt lock off is completely closed when not in use to prevent injury, or damage to vehicle
upholstery.
3
- Press the enhanced child restraint down firmly and pull the vehicle shoulder belt to fasten the enhanced child
restraint securely. (15)-1(15)-2
Ensure to close the lock-off after checking the enhanced child restraint is securely fastened. (15)-3(15)-4
Keep your fingers off when closing the lock-off clips to avoid injury.
The enhanced child restraint can not be used if the vehicle safety belt buckle (female buckle end) is too long
to anchor the enhanced child restraint securely.
Double check that the enhanced child restraint is securely installed and does not move on the vehicle seat.
Correctly assembled vehicle belt is shown as (16)
Ensure that the vehicle lap belt passes through the vehicle lap belt slot. (16)-1
Ensure that the vehicle shoulder belt passes through the rear-facing vehicle belt slot. (16)-2
The vehicle buckle tongue is engaged with the buckle correctly, as
(16)-3
.