NTI Trinity Ti 150 Скачать руководство пользователя страница 6

Страница: 6 / 36

Concentric vent terminal

Use NTI part # 82666 or
York Part# 1CT0303

Roof Venting

Use of existing Chimney

It is permissible to run vent pipe through an existing chimney as long as:

1)  The chimney is not to be used by any other appliance.
2)  Flue gases don’t enter the vacant chimney.
3)  Only Solid Core ABS, PVC

sch.40

, CPVC, or AL294C pipe is used.

Vent lengths are within the maximums specified.

18”

12” Plus
Snow

Must insert
plastic bird
screen

Must be 1”
from wall

Support
(Field installed)

Inlet air

Exhaust

Inlet air

Exhaust

Support
(Field supplied)

Exhaust

24”

Inlet Air

Exhaust

Inlet Air

Roof weather seal
Flashing (field supplied)

Clearances and requirements of this manual
supersede, those of the Instructions enclosed in
vent terminal #650.75-N2, which contain more
detailed assembly instructions.

Note: inlet pipe must
always be connected to
the boiler.

36”
min.

Minimum 12”
plus snow
allowance

4” or greater
than 24”

48” min.

Apply plate here

Gas Vent Directly Below

Keep Free of Obstructions

Содержание Trinity Ti 150





































Результаты поиска

Содержание Trinity Ti 150

Отзывы:

Похожие инструкции для Trinity Ti 150

Бренды по названию

Популярные бренды

NTI Trinity Ti 150, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Trinity Ti 150

Отзывы:

Похожие инструкции для Trinity Ti 150

Бренды по названию

Популярные бренды