background image

 

9

Vent piping outside the Building is permitted under the following conditions: 

1.  The maximum length outside the building is 20 feet. 
2.  Only 3” pipe can be used. 
3.  All normal termination clearances 

are maintained. 

4.  All exterior exhaust vent pipes are 

insulated with 3.5”-ID, ½”-thick 

Closed Cell Foamed Polyolefin 
Tubing

 i.e., “

Tundra Seal Plus”

 or 

equivalent. 

5.  The pipe is supported every 24” 
6.  The exhaust and inlet are sloped 

back to the boiler ½ ” elevation for 
every foot.  

 

 

 

4.0 CONDENSATE DRAIN 

This unit produces water as a 
product of combustion. Much of this 
water condenses on the heat 
exchanger and in the venting 
system. All exhaust piping must be 
on a slope back to the boiler ¼” per 
linear foot of vent. Steps must be taken to ensure that condensate does not collect in the venting 
system. Condensate must be drained from the boiler into a household drain.  
 

Note: check with your municipality, or local gas company to determine if disposal of combustion 
condensate is permitted.  In the State of Massachusetts the condensate must be neutralized 
prior to entering a drain.

  

 
 The following are important notes that must be taken into 
consideration when constructing the condensate system: 

• 

DO NOT

 run condensate line outside. A frozen or blocked 

drain will cause the condensate to fill the combustion 
chamber. This will result in a no heat condition, as the unit 
will shut down, and damage to the flame sensor, and 
components can occur. 

• 

NEVER

 use copper, steel, or galvanized piping in the 

construction of the condensate system. 

• 

When a condensate pump is used or required, select a 
pump that is designed for residential furnaces. 

Warning

 

Failure to properly connect the condensate 
line will cause combustion gases to enter the 
room, possibly causing serious injury to 
occupants or death.  

Insulation

 

“Tundra Seal 

Plus” 3.5” ID. ½” 

thick

 

Supports every 24” 

12” plus 
allowance 
above grade 

Exhaust

Inlet

Maximum of 20 feet is 
permitted for outside a 
building using 3” pipe 
ONLY. 

Apply plate here 

Gas Vent Directly Below 

Keep Free of Obstructions

 

Condensate 
from Boiler 

Bottom 
Panel

 

Condensate 

Trap & drain

Condensate drain 
pipe must 

not

 be 

sealed to allow 
overflow, if blocked.

Condensate 
Siphon 

Содержание Trinity Ti 150





































Отзывы: