nStor NexStor 4200F Series Скачать руководство пользователя страница 29

Страница: 29 / 174

Chapter 1 - Getting Started

Control and Monitoring

An integral part of the NexStor 4200F Series Storage System is its control and

monitor capabilities.

The SES processors provide monitoring data for the enclosure environmental

conditions such as enclosure temperature, cooling fans, power supplies, and FC

Loop status. This data is reported to the monitoring system to provide LED and

audible alarm notifications. This monitored information is also communicated to

external monitoring software.

Refer to “VT-100 Interface Enclosure Monitoring” on page 110 for complete

details.

The RAID Controllers provide monitoring data for its environmental condition

and logical arrays. They communicate that data to the front bezel LEDs,

third-party configuration and monitoring software, and the VT-100

firmware-based interface for management and monitoring. (Refer to the software

user’s guide for configuration, management, and monitoring of the controllers

and logical arrays.)

Front Bezel LEDs and Reset Button Identification

Reset A

larm

Drive Status LEDs

(left column of LEDs)

Power On LED

Channel Status LED

Power Supply Status LED

Fan Status LED

Alarm Reset Button

Drive Activity LEDs

(right column of LEDs)

4200F.book Page 17 Thursday, January 23, 2003 2:47 PM

Содержание NexStor 4200F Series















































































































































































Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды

nStor NexStor 4200F Series, Руководство пользователя

Результаты поиска

Содержание NexStor 4200F Series

Отзывы:

Похожие инструкции для NexStor 4200F Series

Бренды по названию

Популярные бренды