NSD VARICAM VS-5F Series Скачать руководство пользователя страница 96

Страница: 96 / 130

OPERATION

9. HOW TO USE APPLIED FUNCTIONS (SWITCH OUTPUT)

POINT

*1: Repeats procedure

③

and

④

again when returning form the arbitrary pulse mode to

the switch setting (SET) mode.

*2: SW-ON LED and OFF LED switch when [ON / OFF] key is pressed every time.

Turns ON the SW-ON LED when setting the number of pulses.
Turns ON the OFF LED when setting the pulse starting angles.

⑥

Enters the number of pulse.

Presses [SET] key, and then POSITION
display area turns ON.
The number of pulse is entered.

⑦

Turns ON the OFF LED. *2

Presses [ON / OFF] key in order to designate
the pulse starting angle. The OFF LED turns ON.

⑧

Inputs the pulse starting angle.

Inputs the pulse starting angle by
pressing [+] or [-] key of POSITION, and
then the value blinks in the POSITION
display area.
Setting range: 0 to 359.5

If [CLR] key is pressed in this timing, the inputting
value will be canceled.

⑨

Enters the pulse starting angle.

Presses [SET] key, and then POSITION
display area turns ON.
The pulse starting angle is entered.

OFF LED

is ON

By 10

units

By 0.5

units

Displays by 0.5

units

Decimal point is ON : 0.5

Decimal point is OFF : 0.0

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Похожие инструкции для VARICAM VS-5F Series

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Похожие инструкции для VARICAM VS-5F Series

Бренды по названию

Популярные бренды