NSD VARICAM VS-5F Series Скачать руководство пользователя страница 67

Страница: 67 / 130

OPERATION

7. HOW TO USE BASIC FUNCTION

[ 3 ] Selects the Operation (RUN) Mode

Selects the operation (RUN) mode, refer to the procedure [1].

[ 4 ] Operation (RUN)

The switch output turns ON or OFF according to the setting value during the operation.
Indicates the monitor contents during the operation.

Name

Descriptions

①

MODE indicator

RUN LED is ON: Indicates the operation (RUN) mode.

②

PROGRAM display Displays selecting the program number.

(VS-5F and VS-5F-1 are not available this function.)

③

SW / PRM display

Displays the switch number which is selected by SW /PRM key.

④

RDY indicator

If there is no error, this indicator will turn ON when selecting operation (RUN) mode.

This indicator is same condition as “System ready output signal” of the output connector.

⑤

DOG display

Monitors the switch number output state that is selected by SW / PRM key.

ON : OFF :

⑥

POSITION display

Displays the current position value.

⑦

SW / PRM key

Selects the switch number that is monitored on DOG display area.

①

②

③

④

⑤

⑥

⑦

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды