NSD VARICAM VS-5F Series Скачать руководство пользователя страница 58

Страница: 58 / 130

OPERATION

7. HOW TO USE BASIC FUNCTION

●

Parameter List

No.

Name

Description

Setting range

Initial

value

Initial display

Displays “00” at first when selecting the

parameter setting (PRM) mode.

VS-5FX output

specifications

This function must be designated at first

when using VS-5FX(-1) after delivery.

Designates the combination of program

and switch output numbers.

0: 16-program, 40-switch

1: 32-program, 24-switch

ABSOCODER

rotation direction

Designates the rotation direction of

ABSOCODER’s shaft in which the current

position value increase.

0: Increases the current position value by

rotating CW direction.

1: Increases the current position value by

rotating CCW direction.

0: CW direction

Display:

1: CCW direction

Display:

Origin point

setting

Designates the machine’s origin point

(000) to VARICAM.

Current position

setting

Designates the machine's current position

value to VARICAM by the key input.

Setting unit is 0.5

0 to 359.5

7-5-1. Selects the Parameter Setting (PRM) Mode

Keeps pressing [MODE] key more than 1 second.
POSITION and MODE display areas are blinking, and
changes to mode selection screen.

Repeatedly presses [MODE] key, and selects the
parameter setting (PRM) mode.

Presses [SET] key.
Changes to the parameter setting (PRM) mode.

Operation (RUN) mode Switch setting (SET)mode Parametr setting (PRM) mode

PRM LED
is ON

LED ON/OFF state

: ON

: OFF

: BLINK

POINT

The password would be already set if "

" is

displayed. Refer to “ APPENDIX 1”.

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды