NSD VARICAM VS-5F Series Скачать руководство пользователя страница 65

Страница: 65 / 130

OPERATION

7. HOW TO USE BASIC FUNCTION

POINT

*1: SW-ON LED and OFF LED switch when [ON / OFF] key is pressed every time.

Turns ON the SW-ON LED when setting the ON angle.
Turns ON the OFF LED when setting the OFF angle.

*2: ON and OFF angle must be set together.

In the case of setting only ON angle and go to different operation, the screen displays “u17 (‘No setting’ error)”.

⑤

Turns ON the OFF LED. *1

Presses [ON / OFF] key in order to designate
the OFF angle. The OFF LED turns ON.

⑥

Inputs the OFF angle value.

Inputs the OFF angle value by
pressing [+] or [-] key of POSITION, and
then the value blinks in the POSITION
display area.

Setting range: 0 to 359.5

If [CLR] key is pressed in this timing, the inputting
value will be canceled.

⑦

Enters the OFF angle value. *2

Presses [SET] key, and then POSITION
display area turns ON.
The OFF angle value is entered.

⑧

Repeats below procedure.

Repeats procedure

②

⑦

until number of switch outputs which you need.

Operates from procedure

①

when setting the switch output to different program.

By 10

units

By 0.5

units

OFF LED

is ON

Displays by 0.5

units

Decimal point is ON : 0.5

Decimal point is OFF : 0.0

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды