manualshive.com logo in svg

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Поделиться
Скачать
NSD VARICAM VS-5F Series Скачать руководство пользователя страница 106

        

 

 

96 

 

OPERATION 

10. HOW TO USE APPLIED FUNCTIONS (OPERATION MODE) 

  

10-3. Fine-adjust the Switch Output During the Operation 

 
This function is applicable with all VS-5F Series. 
 
Uses this function when the switch output needs to fine-adjust during the operation. 
The fine-adjustment unit is 0.5 degree. 
This function changes in the  operation (RUN) mode after setting the parameter No.92 (setting change during 
operation). 

 

●

  Parameter list 

No. 

Name 

Description 

Setting range 

Initial 

value 

Reference for 

setting procedure 

(Chapter No.) 

92 

Setting change   
during operation

 

Designates the function when   

fine-adjusting the switch output   

during the operation. 

0: Change disable 
1: Change enable

 

0 

8-1-1 

8-1-2 

 
 

Fine-adjusts the switch output according to the following procedures. 

 

①

  Monitors the setting value of the switch output. 

Presses [SET] key, and monitors the setting   
value of the switch output.

 

 
 
 
 

②

  Selects the switch number.

 

Selects the switch number by 
pressing [+] or [-] key of SW / PRM. 

 

③

  Selects the dog number. 

Selects the dog number by   
pressing [+] or [-] key of the dog. 

 

④

  Changes the fine-adjust mode. *1 

Presses 

  key of POSITION, and then the   

value blinks in the POSITION display area. 

 

⑤

  Fine-adjusts the ON angle value. *4 

Fine-adjusts the ON angle value by 
pressing [+] or [-] key of POSITION. 
The value which is fine-adjusted is   
reflected the switch output. 

 

⑥

  Changes the setting value monitoring mode of the switch output. *2 

Presses [SET], and changes the setting   
value monitoring mode of the switch output. 

SW-ON LED 

is ON 

Displays by 0.5

°

units 

Decimal point is ON : 0.5

°

 

Decimal point is OFF : 0.0

°

 

Содержание VARICAM VS-5F Series



































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды