NSD VARICAM VS-5F Series Скачать руководство пользователя страница 19

Страница: 19 / 130

SUMMARY

1. SUMMARY

Function

Description

Serial

communication

(3) Connectable with Touch Panel (VARIMONI)

VARICAM setting data is able to read, edit, write, and print by using the TouchPanel.

Touch Panel can control centrally maximum 16 units of VARICAM.

(4) Connectable with programmable controllers (PLC) which are made by Mitsubishi Electric

Co. or OMRON Corporation.

(5) RS-232C communication

Connecting with a personal computer or programmable controller (PLC), data is able to read,

edit, write, and print by a communication program that is made by the customer.

VS-5F Series supports existing communication protocol of VS-5E Series.

For more details regarding the serial communication, please contact your NSD representative.

Password

This function is applied to all models that are written "SP1" in the lower right portion of the front

panel.

This is the function to ask inputting the password when the mode of VARICAM changes form

the operation (RUN) mode.

Customers can pick and set the password which consists of 3 digits of numeric values.

The mode cannot be changed without the password after setting numbers; therefore, the value

of “switch setting” and “parameter setting” can be protected. It can also be protected from

changing the program No. from panel side.

If the password is not set, the mode could be changed by conventional operation.

Refer to “APPENDIX-1. PASSWORD FUNCTION” for the setting.

PLC

VARICAM

RS-232C, RS-422

Cable

Communication cable Communication cable

Distribution

adapter

Connectable max. 16 units by
multi-drop connection

Touch Panel VARICAM

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды