NSD VARICAM VS-5F Series Скачать руководство пользователя страница 64

Страница: 64 / 130

OPERATION

7. HOW TO USE BASIC FUNCTION

Setting example

Program No. : 1
Switch No. : 1

ON angle

125.5

OFF angle

234.5

7-6-2. Sets the Switch Outputs

Explains the switch output setting procedure below, and it explains using contents of the setting example.

Sets the switch output according to the following procedures.

①

Selects the program number.

Selects the program number by

pressing [+] or [-] key of PROGRAM.

Program number selection range
VS-5F(-1)  : There is not program function.
VS-5FD(-1)  : 0 to 7
VS-5FX(-1)  : 00 to 15 or 00 to 31

②

Selects the switch number.

Selects the switch number by
pressing [+] or [-] key of SW / PRM.

Switch number selection range
VS-5F(-1)  : 01 to 24
VS-5FD(-1)  : 01 to 24
VS-5FX(-1)  : 01 to 40 or 01 to 24

③

Inputs the ON angle value.

Inputs the ON angle value by
pressing [+] or [-] key of POSITION, and
then the value blinks in the POSITION
display area.

Setting range: 0 to 359.5

If [CLR] key is pressed in this timing, the inputting
value will be canceled.

④

Enters the ON angle value

Presses [SET] key, and then POSITION
display area turns ON.
The ON angle value is entered.

OFF

125.5

234.5

By 10

units

By 0.5

units

Displays by 0.5

units

Decimal point is ON : 0.5

Decimal point is OFF : 0.0

SW-ON LED

is ON

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды