NSD VARICAM VS-5F Series Скачать руководство пользователя страница 105

Страница: 105 / 130

OPERATION

10. HOW TO USE APPLIED FUNCTIONS (OPERATION MODE)

(4) Monitoring the rotation speed of ABSOCODER’s shaft

The rotation speed of ABSOCODER’s shaft can be check during the operation.

Name

Descriptions

①

SW / PRM display

When the rotation speed is displayed, the following figure is indicated.

②

DOG, PROGRAM

display

Displays the rotation speed.
The display unit is 1 r/min.
Indicates “1234 r/min” in the above display example.

③

MODE indicator

RUN LED is ON: Indicates the operation (RUN) mode.

④

RDY indicator

If there is no error, this indicator will turn ON when selecting the operation (RUN) mode.

This indicator is same condition as “System ready output signal” of the output connector.

③

①

④

②

Содержание VARICAM VS-5F Series



































































































































Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды

NSD VARICAM VS-5F Series, Технические характеристики и инструкция по эксплуатации

Результаты поиска

Содержание VARICAM VS-5F Series

Отзывы:

Бренды по названию

Популярные бренды