NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 112

background image

056341 Rev. AA

NAVIGAT X Mk 2

Page 5-2

5: Installation

5.2 Electrical Installation

Each gyrocompass system is supplied with either a general or an installation-
specific connection diagram. The connection diagram provides the information
needed to fit and connect all cables required by the gyrocompass system.

Ship's cables are directly connected to screw-down terminals on the main PCB.

Keep all wires running inside the housing as short as possible. Avoid to run
wires from one side of the housing to the other. Route wires connecting to TB1
or TB2 through the inlets on the left hand side of the housing and wires con-
necting to TB3 through the inlets on the right hand side.

5.3 Gyrosphere Installation

When the compass housing has been mounted and the system is wired up so
far that supply power is available, works should continue with the installation
of the gyroshpere into the gyrosphere container and the mounting of the as-
sembled container in the compass.

If the system is wired up completely, the installer may alternatively carry out
the initial system configuration before the gyrosphere is installed.

The procedure for installing the gyrosphere is described in Chapter 8.

Warning

Warning

When the compass is energized (24 VDC main and/or backup supply present),
the gyrosphere operating voltage of 100 VAC @ 337 Hz is present on the main
PCB, the gyrosphere supply lines and accross the gyrosphere contacts.
When wiring up the system, make sure the compass' main and backup power
supplies are switched off and safeguarded against accidental switching-on.

Insert the ship's cables through the
inlets at the sides of the compass
housing. Remove the outer cable
covers, draw back the cable shields
and fasten the cables with clamps
or cable bands to the threaded
studs.

To connect the individual wires, re-
move the upper parts of the termi-
nal blocks from their sockets. After
wiring, put the upper parts back into
the sockets and fasten them with
the securing screws.

Caution

The gyrosphere may be installed by authorized service personnel only.

«
...
44
45
46
47
48
...
»

Содержание Sperry Marine NAVIGAT X MK 2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренд: Kawai Страницы: 2

Бренд: Datron Страницы: 197

Бренд: Larson Davis Страницы: 193

Бренд: Facom Страницы: 116

Бренд: Campbell Страницы: 22

Бренд: Campbell Страницы: 32

Бренд: Campbell Страницы: 40

CR3000 Micrologger

Бренд: Campbell Страницы: 12

Бренд: R.M. Young Страницы: 8

Бренд: Campbell Страницы: 21

Бренд: Vanguard Instruments Company Страницы: 62

Бренд: Vanguard Instruments Company Страницы: 58

Бренд: Keeler Страницы: 68

Бренд: KALEAS Страницы: 64

Бренд: ADA INSTRUMENTS Страницы: 27

Бренд: Omega Страницы: 13

Бренд: Avery Weigh-Tronix Страницы: 54

IMI Sensors Spindler 607A61

Бренд: PCB Piezotronics Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды