NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 112

background image

056341 Rev. AA

NAVIGAT X Mk 2

Page 2-4

2: Operation

2.5 Adjusting the Display Brightness

2.6 Acknowledging Alarms / Muting the Audible Alarm

2.7 Optional Functions

The following functions are available only if the gyrocompass system is
equipped with the respective optional controls.

2.7.1

Acknowledging Alarms Remotely

On alarm, acknowlede the alarm from a remote device (e.g. a central alarm
panel). The audible alarm is muted. The alarm message will remain on the dis-
play screen until the alarm is confirmed at the operating unit.

Press key to increase the display brightness.

Press key to reduce the display brightness.

On alarm, press keys to acknowledge the alarm and clear the
alarm message from the display screen. The audible alarm is
muted simultaneously.

On alarm, press keys to mute the audible alarm.
The alarm message will remain on the display screen until the
alarm is acknowledged at the operating unit.

Note

When the cause of an alarm is eliminated, a pending alarm message is cleared
from the display and the audible alarm is muted automatically.
When an alarm has been confirmed, the ext. alarm status output will remain ac-
tive until the cause of the alarm is eliminated.

«
...
14
15
16
17
18
...
»

Содержание Sperry Marine NAVIGAT X MK 2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренд: C-LOGIC Страницы: 2

HF scientific AccUView LED

Бренд: Watts Страницы: 40

WALLACE & TIERNAN P7 ADVANCED

Бренд: Evoqua Страницы: 98

Бренд: Hanna Instruments Страницы: 2

Бренд: Sur-Gard Страницы: 12

Бренд: PASCO Страницы: 2

Analite NEP-5000

Бренд: Observator Instruments Страницы: 103

Бренд: Clavia Страницы: 13

Бренд: Agilent Technologies Страницы: 198

EA Heightmaster +

Бренд: PROLEC Страницы: 38

Photo Set Strato S-20

Бренд: Fisso Страницы: 2

Бренд: ATIM Страницы: 25

Бренд: AlazarTech Страницы: 60

Бренд: Kobold Страницы: 12

Бренд: R&S Страницы: 35

WattNode Plus WNC-3D-240-FT10

Бренд: CCS Страницы: 43

Nunes Instruments Propeller Type Water Current...

Бренд: V-tech Страницы: 19

Бренд: ATI Technologies Страницы: 70

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды