NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 112

background image

NAVIGAT X Mk 2

056341 Rev. AA

5: Installation

Page 5-1

5 Installation

The NAVIGAT X Mk 1 gyrocompass system comprises a compass housing com-
plete with installed baseplate assembly and main PCB, a gyrosphere container,
a gyrosphere and an installation and replacement parts kit.

The gyrosphere is contained in a carrying box, which is packed in a transport
container. This transport container is completely suitable for transport by air,
sea, rail and road.

Until installation, the carrying box containing the gyrosphere is to be stored in
its original transport container. Upon installation, the carrying box with the gy-
rosphere is to be removed from the transport container and is to be carried by
hand directly to the place of installation.

5.1 Installing the Compass Housing

The compass housing is to be attached to a level surface, e.g. a floor or console
by means of six M10 bolts or welding studs (to be supplied by the shipyard). At
the location of the compass, proper ventilation must be ensured and sufficient
space provided for the housing to be opened and maintenance work to be car-
ried out.

For the amount of space required, the attachment points and the position of the
cable inlets, refer to dimension drawing 4991-0112-01.

In the horizontal plane, the compass may be installed at any angle with respect
to the vessel‘s longitudinal axis. Alignment error (i.e. the angle between the
compass‘ and the vessel‘s longitudinal axis) is corrected electronically by set-
ting the alignment error correction value in the Service Setup 1.

Caution

The gyrosphere is always to be transported in the original transport container.
Do not throw or drop the transport container.
The transport container is to be transported in an upright position only.

Caution

Carry the carrying box containing the gyrosphere by hand only and handle it
with extreme care. Remove the gyroshpere from the carrying box only if re-
quired for immediate installation.

«
...
43
44
45
46
47
...
»

Содержание Sperry Marine NAVIGAT X MK 2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренд: Campbell Страницы: 25

Бренд: Larson Davis Страницы: 2

Бренд: G-Tek Страницы: 27

Бренд: Gardner Bender Страницы: 4

Бренд: GAPS Страницы: 36

Бренд: yellow jacket Страницы: 26

Бренд: IEI Technology Страницы: 85

Бренд: JAMAR Technologies Страницы: 4

Бренд: Jamar Страницы: 60

Бренд: ISKRAEMECO Страницы: 12

RAVTD1760WS Series

Бренд: Ravaglioli Страницы: 24

Бренд: Nidec-Shimpo Страницы: 6

micro-TRI-gloss ?

Бренд: BYK Страницы: 174

DT4120 PS Series

Бренд: Datcon Страницы: 92

Бренд: Elcontrol Страницы: 7

FrameSaver SLV Series

Бренд: Paradyne Страницы: 39

Бренд: Opus Technologies Страницы: 24

Бренд: Bitzer Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды