NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 112

background image

056341 Rev. AA

NAVIGAT X Mk 2

Page 6-6

6: System Configuration

Pos. Input

Function:

Selects the position data input protocol

Settings: NMEA-GLL

Position is read from the NMEA $--GLL sentence

NMEA-GGA

Speed is read from the NMEA $--GGA sentence

Sens. D.M. Outp.

Function:

Selects the NMEA output sentence for magnetic heading data at the
Sens Data output

Settings: NMEA-HCHDM

Magnetic heading is transmitted using the NMEA $HCHDM sen-
tence. The transmitted value is the magnetic heading as displayed
on the NAVIGAT X Mk 2 display, i.e. with all corrections applied
according to calibration and magnetic variation settings.

NMEA-HCHDT

Magnetic heading is sent using the NMEA $HCHDTsentence. The
transmitted value is the magnetic heading as displayed on the NAV-
IGAT X Mk 2 display, i.e. with all corrections applied according to
calibration and magnetic variation settings.

NMEA-HCHDG

Magnetic heading is sent using the NMEA $HCHDG sentence. The
sentence includes the raw magnetic sensor heading and values for
deviation and variation.
If the magnetic heading input is configured to read the $--HDG sen-
tence and a deviation value is received, this value is copied to the
output sentence. Otherwise, the deviation value is the correction
applied according to the calibration table.
If the magnetic heading input is configured to read the $--HDG sen-
tence and a variation value is received, this value is copied to the
output sentence. Otherwise, the variation value is the variation as
set in the Manual Settings menu.

«
...
56
57
58
59
60
...
»

Содержание Sperry Marine NAVIGAT X MK 2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренд: Igema Страницы: 30

Бренд: z-laser Страницы: 62

Бренд: Yamaha Страницы: 2

Бренд: Cablescan Страницы: 58

Бренд: Keithley Страницы: 55

TEC SourceMeter 2510

Бренд: Keithley Страницы: 244

Бренд: Kawai Страницы: 112

Бренд: VEE GEE Страницы: 2

Бренд: QALCOMET Страницы: 52

Бренд: Unior Страницы: 2

Бренд: Vaisala Страницы: 83

SF6 Portable Monitor

Бренд: Bacharach Страницы: 2

Бренд: Agilent Technologies Страницы: 198

Бренд: Deprag Страницы: 28

Бренд: Hanna Instruments Страницы: 32

Бренд: Factair Страницы: 38

Бренд: A&D Страницы: 23

Бренд: B meters Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды