NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 85

Страница: 85 / 112

NAVIGAT X Mk 2

056341 Rev. AA

8: Gyroshpere Installation and Service

Page 8-15

13) Take the protective capsule containing the empty phial of mercury and in-

sulating fluid from the installation and replacement parts kit. Remove the
phial from the capsule and open it.

10) Unscrew the 4mm Allen-head screws at-

taching the two halves of the gyroshere
container.

11)

Put the screws and washers aside, mak-
ing sure they won't be lost or fall to the
ground.

12) Take off the upper section of the gyro-

sphere container and place it upside
down on the work surface.

Caution

Take care not to damage the contact pins.

14) Assemble the syringe and cannula. In-

sert the syringe into the recess of the gy-
rosphere. Draw up the mercury and insu-
lating fluid completely.

Warning

Spilt mercury will evaporate and give off poisonous fumes.
Collect spilt mercury with the syringe provided in the installation and replace-
ment parts kit and seal it in the phial for the mercury and insulating fluid.

Содержание Sperry Marine NAVIGAT X MK 2
















































































































Результаты поиска

Содержание Sperry Marine NAVIGAT X MK 2

Отзывы:

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренды по названию

Популярные бренды

NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2, Руководство по сборке

Результаты поиска

Содержание Sperry Marine NAVIGAT X MK 2

Отзывы:

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренды по названию

Популярные бренды