NORTHROP GRUMMAN Sperry Marine NAVIGAT X MK 2 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 112

background image

NAVIGAT X Mk 2

056341 Rev. AA

6: System Configuration

Page 6-13

6.2.3

Technical Pages – Parameters

6.2.3.1

Software Version

6.2.3.2

Update Software

Initiates a software update via the service interface. This feature is for factory
use only. Field service is required to exchange the software flash-memory to
update the system software.

6.2.3.3

Correction Val.

Function:

Displays detailed hard- and software version information

Displays: Hardware

The revision code of the main PCB.

SW Ver.

The creation date of the system software.

Masterboard

The version code of the system software.

Display Board

The version code of an external Control and Display unit, if present.
If no external unit is connected, dashes are shown.

Function:

Sets the correction values for the on-board temperature and gyro-
sphere current measurement

Settings: Corr. Val. Temp.

Temperature correction value. Adjusts the measured value to show
the gyrosphere ambient temperature.
Correction range is -99.9 – +99.9 °C.

Gyro Current Gain

Gain factor for the gyrosphere current. Adjusts the measured value
to show the current flowing through the gyrosphere.
Correction range is 0.000 – 9.999, where a setting of 1.000 equals
unity gain, i.e. no correction.

Note

The correction values are set in the factory. These must not normally be altered.
However, when the system software is exchanged, the values will be lost and
must be re-entered manually.
The correction values are specific to the respective main PCB.

«
...
63
64
65
66
67
...
»

Содержание Sperry Marine NAVIGAT X MK 2

















































































































Отзывы:

Нет отзывов

Похожие инструкции для Sperry Marine NAVIGAT X MK 2

Бренд: Kawai Страницы: 2

Бренд: Datron Страницы: 197

Бренд: A&D Страницы: 102

Бренд: Keysight Страницы: 92

Бренд: PICO Страницы: 2

Бренд: Eurotron Страницы: 122

Trimble Ranger 3

Бренд: Badger Meter Страницы: 20

Бренд: A&D Страницы: 38

Бренд: Vanguard Instruments Страницы: 85

Бренд: Omega Страницы: 4

Бренд: Racelogic Страницы: 15

Photo Set Strato S-20

Бренд: Fisso Страницы: 2

Бренд: PHYWE Страницы: 6

Бренд: LOVATO ELECTRIC Страницы: 9

Бренд: National Instruments Страницы: 40

Бренд: Hioki Страницы: 16

Micropilot S FMR 53 Series

Бренд: E+H Страницы: 12

Бренд: SmarTire Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды