Nortek Security & Control MIGHTY MULE MM272 Скачать руководство пользователя

Страница: 12 / 40

MM272 Installation Instructions

MIGHTY MULE MM272 DUAL GATE OPENER

_____________________________________

DRIVE

_____________________________________

• Low friction screw drive (linear actuator) rated for -5 °F to +160 °F (-20 °C to +71 °C).

• Powered by a 12 V motor with integral case hardened steel gear reducer. Motor speed reduced to 260 rpm. Generates

520 inch lb. of torque at 12 V.

• Maximum opening arc of 110°. Approximate opening time (90°): 18 seconds, depending on weight of gate.

_____________________________________ POWER _____________________________________

• The system is powered by a 12 Vdc automotive, lawn tractor or marine battery (required but not included).

• Battery charge is 120Vac to 16Vac output through the control board] or by optional Solar Panels; the panel should

generate minimum of 10 Watts (600 mA). A diode on the control board prevents battery discharge.

IMPORTANT:

Never use

both

transformer and solar panel— this will damage the battery and control board.

• One (1) blade-style fuse is rated for 15A.

NOTE: The transformer should not be directly connected to any battery. Do not replace fuses with
higher ampere rated fuses; doing so will void your warranty and may damage your control board.

_____________________________________ CONTROL _____________________________________

• Microprocessor-based control board is set for dual leaf, pull-to-open gate installations. Jumper can be removed to

accommodate an optional kit for push-to-open gates.

• Control board has temperature compensated circuits.

• Auto-memorization of digital transmitter code.

• Opener length with push-pull tube fully retracted is 26

", mounting point to mounting point. Maximum stroke is 13".

• Adjustable auto-close timer (OFF to 3–120 seconds), and Dual Sense Technology™ stall force).

• Power terminal block accommodates a transformer or solar panels.

• Accessory terminal block fully compatible with all Mighty Mule access controls.

• Control board allows connection of edge sensors and photoelectric sensors.

• Audio entrapment alarm sounds if unit encounters an obstruction twice while opening or closing.

_____________________________________ OPERATIONAL CAPACITY _____________________________________

• Maximum gate size: 300 lbs., 12' long.

NOTE: BALL BEARING HINGES SHOULD BE USED ON ALL GATES WEIGHING OVER 250 LB.

Technical Specifications

Содержание MIGHTY MULE MM272









































Результаты поиска

Содержание MIGHTY MULE MM272

Отзывы:

Похожие инструкции для MIGHTY MULE MM272

Бренды по названию

Популярные бренды

Nortek Security & Control MIGHTY MULE MM272, Руководство по установке

Результаты поиска

Содержание MIGHTY MULE MM272

Отзывы:

Похожие инструкции для MIGHTY MULE MM272

Бренды по названию

Популярные бренды