Nortec NHRS 010-090 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 70

background image

Installation | 22

External Controls

Control Wiring

The following information is relevant to all controls, factory supplied or otherwise. For wiring use
a minimum of 18 AWG and keep as short as possible. The NHRS humidifier can be operated
with a modulating input or as On/Off.

Control Location

Figure 13: Control Location (Duct Humidification)

Duct Humidification

1

Air Proving Switch



Locate so that it can sense air flow, or lack thereof.

2

Duct High Limit



NHRS operates with On/Off control.



Locate at least 10 feet (3.0 m) from steam distributor, or far enough that steam is
fully absorbed under normal conditions.

3

Humidity Control



NHRS can be modulating, On/Off, or a humidity sensor.



Can be located either in return air duct (preferred) or in room being humidified.



Mount in area representative of room humidity (draft, doorways, sunlight, or
overhang such as shelf can affect reading). Avoid placing near discharge diffuser of
humidified air.

4

Outdoor Temperature Sensor



Mount in area representing outdoor air temperature (makeup air duct, outside).

Caution:

Failure to wire the humidifier in accordance with the wiring instructions

could cause permanent damage. Such errors will void the warranty.

«
...
23
24
25
26
27
...
»

Содержание NHRS 010-090







































































Отзывы:

Нет отзывов

Похожие инструкции для NHRS 010-090

Бренд: UltraCOOL Страницы: 2

Бренд: Dantherm Страницы: 15

Бренд: Black+Decker Страницы: 64

STEAMaster+ SERIES

Бренд: SATA Страницы: 44

SeccoReale Elettronico

Бренд: Olimpia splendid Страницы: 20

Бренд: TaoTronics Страницы: 23

Бренд: Haier Страницы: 15

Бренд: Haier Страницы: 35

Бренд: Haier Страницы: 28

Бренд: Haier Страницы: 35

Бренд: Haier Страницы: 8

Бренд: Saivod Страницы: 128

Бренд: LG Страницы: 30

Бренд: LG Страницы: 32

Бренд: LG Страницы: 20

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренд: LG Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды