Nortec NHRS 010-090 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 70

background image

Installation | 10

Location



Mount on a suitable wall or vertical surface. Do not sit the unit on the floor to allow
clearances required for plumbing and electrical connections.



Clearance dimensions shown are for reference only and are the minimum required for
maintenance of the humidifier. Consult local and national codes before final location
and installation. Nortec does not accept responsibility for installation code violations.



Install only in areas with ambient temperatures between 41 and 104ºF (5 and 40ºC),
and relative humidity between 5 and 95% (non-condensing).



When possible, install the humidifier below the steam distributor. If mounted above the
steam distributor, take care to provide proper steam line routing and proper condensate
traps.



DO NOT locate the humidifier any further than absolutely necessary from the steam
distributor location as net output will be reduced as a result of heat loss through the
steam line.



When possible, mount the humidifier at a height convenient for servicing.

Figure 5: Mounting Location / Clearance

Note:

Do not mount on hot surfaces, where freezing can occur, vibrating surfaces, or

floor.

«
...
11
12
13
14
15
...
»

Содержание NHRS 010-090







































































Отзывы:

Нет отзывов

Похожие инструкции для NHRS 010-090

STEAMaster+ SERIES

Бренд: SATA Страницы: 44

Бренд: East Страницы: 12

Бренд: TecLime Страницы: 38

Бренд: omi Страницы: 75

Бренд: Aikyo Страницы: 12

Бренд: HoMedics Страницы: 48

Бренд: Wood’s Страницы: 7

Бренд: Aprilaire Страницы: 2

Бренд: Star-Light Страницы: 100

Бренд: ZOESURE Страницы: 16

Бренд: GeneralAire Страницы: 2

Бренд: Livart Страницы: 7

Бренд: SMC Networks Страницы: 52

ElectroVap ELMC 10 EG

Бренд: Devatec Страницы: 40

Бренд: Fakir Страницы: 36

Бренд: Home Страницы: 20

Бренд: Noaton Страницы: 26

Бренд: Qlima Страницы: 240

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды