Nortec NHRS 010-090 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 70

background image

Installation | 14

Steam Distributor



Steam generated by the NHRS may be distributed directly into a conditioned
environment with a Remote Blower Pack (P/N 2572615), or into an air handling system
using either Nortec steam distributors or Nortec’s SAM-e steam distribution manifold.



The steam distributor should be installed as close as possible to the humidifier. Short
steam distribution lines minimize condensate losses and the possibility of generating
back pressure in the steam distribution line.



Figure 8 provides common guidelines for locating a steam distributor in a duct.

Figure 8: Distributor Location in Duct

Note:

• Install the NHRS as close as possible to whatever steam distributor is used.
• Refer to distributor, SAM-e, or Remote Blower Pack installation manuals for detailed

installation instructions (2556592, 1507619, and 2572641, respectively)

«
...
15
16
17
18
19
...
»

Содержание NHRS 010-090







































































Отзывы:

Нет отзывов

Похожие инструкции для NHRS 010-090

Бренд: AC Infinity Страницы: 32

Бренд: GMC Страницы: 20

Бренд: German pool Страницы: 16

23-11-2242N-005

Бренд: Maytag Страницы: 16

Бренд: HoMedics Страницы: 9

Бренд: ElectrIQ Страницы: 24

Бренд: Germ Guardian Страницы: 8

Бренд: CADPXS Страницы: 13

Бренд: Silvercrest Страницы: 36

Бренд: Silvercrest Страницы: 54

Бренд: Silvercrest Страницы: 80

Бренд: Silvercrest Страницы: 88

Бренд: Silvercrest Страницы: 100

Бренд: Timberk Страницы: 28

Бренд: TOTALINE Страницы: 8

Бренд: Waykar Страницы: 20

HeatSink HSH Series

Бренд: ZEKS Страницы: 20

Бренд: Zelmer Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды