Nordson ProBlue P10 Скачать руководство пользователя страница 288

Страница: 288 / 319

SP Pump Diagnostics and Repair

D-28

Part 1024496_06

2014

Nordson Corporation

Disassemble the Lower Ball Seat and the Pressure Ball Assemblies

See Figure D‐14.

1. Pull the siphon ball cage (1) off of the lower ball seat (4), and then

remove the siphon ball (2).

2. Remove the O‐ring (3) from the lower ball seat.

See Figure D‐15.

3. Unscrew the pressure ball seat (3) from the piston (1), and then remove

the pressure ball (2).

Check/Repair

Siphon ball
P/N 900001

Pressure ball
P/N 900000

Char buildup

Ball seats

P/N 1017320

Char buildup or damage

Apply Never‐seez during
reassembly

Siphon ball cage

P/N 503696

Char buildup or damage

Lower ball seat O‐ring

P/N 945037

Nicked, gouged,
deteriorated, or swollen

Apply Parker lubricant
during reassembly

NOTE:

Clean all hydraulic components in a container of Type R fluid before

reassembling them.

Special Reassembly Instructions

If the siphon ball cage does not fit tightly onto the lower ball seat, gently
bend the legs of the cage together to create a spring‐fit onto the seat.

Содержание ProBlue P10
































































































































































































































































































































Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды

Nordson ProBlue P10, Руководство пользователя по изделию

Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды