Nordson ProBlue P10 Скачать руководство пользователя страница 135

Страница: 135 / 319

Troubleshooting

6-17

Part 1024496_06

2014

Nordson Corporation

DP.5 Check the Resistance of the Tank and Manifold Heaters

WARNING!

Risk of electrocution! Ensure that disconnect switch that serves

the melter is in the off position and locked.

1. De‐energize the melter. Refer to Section 1,

Safety

See Figure 6‐1.

2. Disconnect the power harness plug (P/N 1024529) from receptacle J6 on

the main board.

3. Measure the resistance across pins 1 and 2 (tank) or pins 3 and 4

(manifold) on the power harness plug, and then do

one

of the following:

If the resistance

within the range shown in Table 6‐6, go to step 4.

If the resistance is

not

within the range shown in Table 6‐6, go to step

NOTE:

Refer to Appendix E for 400/480 Volt heater resistance data.

Table 6‐6 Heater Resistance

Resistance

Model

Tank

Manifold

46–58 ohms

40–50 ohms

P10

4. Individually check the resistance between the chassis and pins

1 and 2 (tank) or pins 3 and 4 (manifold) on the power harness plug, and
then do

one

of the following:

If the resistance is greater than 1 Meg ohm, return to the
troubleshooting chart.

If the resistance is less than 1 Meg ohm, go to step 5.

5. Remove the front and rear panels from the melter. Refer to Section 5,

Cleaning the Melter

, for the procedure to remove the panels.

CAUTION!

Use two wrenches and minimal force when loosening or

tightening the heater terminal connections. Using a single wrench or
excessive force to remove or tighten the terminals nuts can damage the
heater.

Содержание ProBlue P10
































































































































































































































































































































Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды

Nordson ProBlue P10, Руководство пользователя по изделию

Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды