Nordson ProBlue P10 Скачать руководство пользователя страница 278

Страница: 278 / 319

SP Pump Diagnostics and Repair

D-18

Part 1024496_06

2014

Nordson Corporation

Remove the Shifter Fork

CAUTION!

Handle the shifter fork with care. Dropping or otherwise

mishandling the shifter fork may damage the magnet.

See Figure D‐9.

1. Remove the hex‐head screw (2) and the washer (1 ) from the shifter

fork (3).

2. Remove the shifter fork from the piston by sliding the fork up to the

narrowest point on the piston.

Check/Repair

Shifter fork assembly

P/N 166880

Word “UP” is facing
upwards

Securely attached to
piston

Resting on piston
shoulder

Bent

Magnets
secure/undamaged

Replace fork if bent or
magnet is damaged

Special Reassembly Instructions

The fork must be resting on the shoulder of the piston (See Figure D‐9,
item 4).

The word “UP” must be facing the top of the pump frame.

Содержание ProBlue P10
































































































































































































































































































































Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды

Nordson ProBlue P10, Руководство пользователя по изделию

Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды