Nordson ProBlue P10 Скачать руководство пользователя страница 133

Страница: 133 / 319

Removing a hose/gun
module

Troubleshooting

6-15

Part 1024496_06

2014

Nordson Corporation

DP.3 Check the Operation of the Power Relay or Thermostats

The pre‐conditions for this diagnostic procedure are as follows:

The heater LED is illuminated.

Indicator DS2 on the main board is

not

illuminated.

Indicators DS5 and DS6 on all hose/gun modules are

not

illuminated.

1. De‐energize the melter. Refer to Section 1,

Safety

2. Remove all of the hose/gun modules.

3. Re‐energize the melter.

NOTE:

If an F1 fault re‐occurs after re‐energizing the melter, reset the

melter and turn the heaters back on.

4. Press the

Heaters

key.

See Figure 6‐1.

5. Check indicator DS2 on the main board, and then do

one

of the following:

If indicator DS2

does

illuminate, go to step 6.

If indicator DS2 does

not

illuminate, got to step 7.

6. Locate a failed hose/gun module by

individually

replacing and checking

each module as follows:

a. De‐energize the melter.

b. Replace the hose/gun module.

c. Re‐energize the melter.

d. Check if LED DS5 illuminates.

Replace the hose/gun module that causes LED DS5

not

to illuminate

when the melter is re‐energized.

7. Complete

one

both

of the following checks to determine if the main

board or a thermostat has failed:

a. Check for 21–27 VDC across receptacle J9, pins 1 and 6. If the

voltage is

incorrect

, replace the main board, otherwise go to b.

b. Check for 21–27 VDC across receptacle J9, pins 2 and 6. If the

voltage is

incorrect

, one or both of the thermostats or the wire harness

connected to receptacle J7 has failed. Refer to

DP.6 Check the

Resistance of the Tank/Manifold Thermostat

. If the voltage is

correct

replace the main board.

Содержание ProBlue P10
































































































































































































































































































































Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды

Nordson ProBlue P10, Руководство пользователя по изделию

Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды