Nordson ProBlue P10 Скачать руководство пользователя страница 161

Страница: 161 / 319

Troubleshooting

6-43

Part 1024496_06

2014

Nordson Corporation

Problem

Turn on or adjust the plant air
pressure.

−

Is air being supplied to the top of
the pump?

Is 24 VDC being supplied to the
solenoid valve (wire harness
leads 9 and 10)?

Replace the pneumatic
assembly.

P/N 1028307.

−

Are the yellow and green air lines
to the pneumatic assembly
connected properly?

See Figure 6-4.

Do the wires at Pins 9 and 10 on
the J7 wire harness lack
continuity?

Connect securely. See Figure
6-2.

Replace the J7 wire harness.

P/N 1024600.

Connect securely.

Replace the main board.

P4/P7

−

P/N 1028322.

P10

−

P/N 028323.

−

Is the air supply to the melter
turned off or is the plant air
pressure low?

−

Is the operating air pressure set
correctly?

Refer to

Section 4.

Adjust the operating air
pressure for the current
manufacturing process.

Continued

on next

page....

Starting conditions:

No faults

Ready LED is illuminated

No hot melt output from all guns

Pump has stopped

Pump LED is illuminated

Tank set-point temperature is OK

Pump is not controlled by a remote input

T.4.2

Содержание ProBlue P10
































































































































































































































































































































Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды

Nordson ProBlue P10, Руководство пользователя по изделию

Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды