Nordson ProBlue P10 Скачать руководство пользователя страница 282

Страница: 282 / 319

SP Pump Diagnostics and Repair

D-22

Part 1024496_06

2014

Nordson Corporation

Remove the Pump Frame and the Insulator

See Figure D‐11.

1. Remove the four hex‐head screws (1) and washers (4).

2. Lift the pump frame (2) and the insulator (3) off of the piston.

See Figure D‐12.

3. If necessary (see Checks/Repairs), remove the retaining ring (1) and the

U‐cup (2) from the frame.

Check/Repair

Pump insulator

P/N 1017307

Cracked or warped

U‐cup piston seal

P/N 952100

Nicked, cut, or
deteriorated

Apply Parker lubricant
during reassembly

Special Reassembly Instructions

Before reinstalling the insulator and pump frame, place the O‐ring and
piston seal over the piston.

NOTE:

Install the pump seal with the open side facing the pump body.

Install the insulator with the words “This side up” facing upwards.

Use the insulator to seat the O‐ring and pump seal into the groove in the
pump body.

The tapered end of the insulator and pump frame face the filter.

Содержание ProBlue P10
































































































































































































































































































































Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды

Nordson ProBlue P10, Руководство пользователя по изделию

Результаты поиска

Содержание ProBlue P10

Отзывы:

Похожие инструкции для ProBlue P10

Бренды по названию

Популярные бренды