Nordson Encore Скачать руководство пользователя страница 95

Страница: 95 / 97

Nordson Corporation

Westlake, Ohio

DOC14049-02

EU DECLARATION of Conformity

Product: Encore Engage Powder Spray Systems

This Declaration is issued under the sole responsibility of the manufacture.

Models:

Encore Main Controller with Display, Encore Main Controller with Remote Display, Encore Engage

Auxiliary Units

Description:

This is an electrostatic, powder spray system, including Manual and Auto applicators, control

cables and associated controllers.

Applicable Directives:

2006/42/EC - Machinery Directive

2014/30/EU - EMC Directive

2014/34/EU - ATEX Directive

Standards Used for Compliance:

EN/ISO12100 (2010) EN61000-6-3 (2007) FM 7260 (2018) EN50050-2 (2013)

EN61000-6-2 (2005) EN55011 (2009) EN50177 (2012)

Principles:

This product has been designed & manufactured according to the Directives & standards / norms described

above.

Type of Protection:

- Ambient Temperature: +15ºC to +40ºC

- Ex tb IIIB T60ºC / Ex II 2 D / 2mJ = (Encore XT and HD Manual Applicators)

- Ex tc IIIB T60ºC Dc / Ex II (2) 3 D = (Enhance Manual Interface Controller)

- Ex II (2) D = (Engage Controllers and Remote Display) – Located in Unclassified Location (Zone)

- Ex II 2 D / 2mJ = (Encore Auto Applicator)

Certificates:

- FM14ATEX0051X = Encore XT and HD Manual Applicators (Norwood, Mass. USA)

- FM18ATEX0058X = Encore Enhance Manual Interface (Norwood, Mass. USA)

- FM11ATEX0056X = Encore Automatic Applicator (Norwood, Mass. USA)

- FM19ATEX0005X = Encore Engage Controller (Norwood, Mass. USA)

ATEX Surveillance

- 1180 SGS Baseefa (Buxton, Derbyshire, UK)

___________________

Date:

24Sept19

Jeremy Krone

Supervisor Product Development Engineering

Industrial Coating Systems

Amherst, Ohio, USA

Nordson Authorized Representative in the EU

Contact:

Operations Manager

Industrial Coating Systems

Nordson Deutschland GmbH

Heinrich-Hertz-StraBe 42-44

D-40699 Erkrath

Содержание Encore
































































































Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды

Nordson Encore, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды