Nordson Encore Скачать руководство пользователя страница 70

Страница: 70 / 97

Repair

5-6

Part 1618871

−

2020 Nordson Corporation

Touchscreen Replacement

(contd)

See Figure 5-12.
5. Support touchscreen (5) from front of door or remote display case while

removing the allen screws (6) and brackets (7) securing the

touchscreen.

6. Remove the touchscreen out the front of the door or remote display

case.

7. Place the new touchscreen through front opening of door or remote

display case.

8. Support the touchscreen in the opening while installing brackets and

allen screws. Torque allen screws to 5.5

−

6.0 in-lb (0.6

−

0.7 N

m).

9. Reconnect ground, Ethernet, and power harness connections.
10. Mark the matching IP address noted earlier on the IP label (shown in

Figure 5-1 1) of the new touchscreen before closing cabinet or remote

display.

11. Complete software update using USB.

Содержание Encore
































































































Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды

Nordson Encore, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды