Nordson Encore Скачать руководство пользователя страница 20

Страница: 20 / 97

System Overview

2-8

Part 1618871

−

2020 Nordson Corporation

Special Conditions of Use

1. The Encore Engage Control Consoles and Remote Display are only for

use in non-explosive atmospheres.

2. The Encore Engage Control Consoles and Remote Display shall be

used with the manufactures applicators that are certified under

FM11ATEX0065X, FM13ATEX0006X or FM14ATEX0051X and for

manual applicators shall be used with the kit including the manual

interface unit certified under FM18ATEX0058X.

3. The equipment must be used in accordance with EN 50177 for

automatic applicators and EN 50050-2 for manual applicators.

The Encore Engage Main Console with display and the Auxiliary Consoles

and Remote Display with Main Console for shall be used within the ambient

temperature range of +15

C to +40

C with Encore Automatic or Encore HD

Automatic Powder Applicators.

The Encore Engage Main Console with display and the Auxiliary Consoles

and Remote Display with Main Console shall be installed in a non-explosive

atmosphere location.

CAUTION:

Caution should be taken when cleaning plastic services on the

Encore Engage consoles and Remote Display. There is a potential for static

electricity buildup on these components.

Approval Labels

The following figures show the content of the approvals labels on the

system cabinets.

Figure 2-4

Label for CE ATEX Approval (On Main and Auxiliary Cabinets)

Содержание Encore
































































































Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды

Nordson Encore, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды