Nordson Encore Скачать руководство пользователя страница 13

Страница: 13 / 97

System Overview

2-1

Part 1618871

−

2020 Nordson Corporation

Section 2

System Overview

This manual covers the system controls hardware for Encore

Engage

system controllers.

NOTE:

The system also requires external part ID sensors such as

photoeyes or scanners for part identification and zone detection.

See Figure 2-1. The following Encore Engage controllers are available:

Encore Engage Main System Controller

−

Includes touchscreen

controls and supports 4

−

16 powder spray guns

Encore Engage System Controller with Remote Interface
Controller

−

Supports 4

−

16 powder spray guns with remote controller

for interface controller mobility

Encore Engage Auxiliary Controller

−

Provides support for adding an

additional 2

−

16 spray guns

Encore Engage

Main System Controller

Encore Engage

Auxiliary Controller

Encore Engage Main System

with Remote Controller

Figure 2-1

Encore Engage Controllers

Содержание Encore
































































































Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды

Nordson Encore, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды