Nordson Encore Скачать руководство пользователя страница 42

Страница: 42 / 97

Installation

3-18

Part 1618871

−

2020 Nordson Corporation

Spray Gun Cable Connections

See Figure 3-10. Connect the automatic spray gun cables to the

receptacles on the rear panel of the Engage console. Connect spray gun 1

cable to receptacle 1, spray gun 2 cable to receptacle 2, and so on.

Odd Number of Spray Guns

Engage systems are sold configured for an even number of spray guns.

Each spray gun controller card in the console controls two spray guns. If

the system is configured for an odd number of spray guns, the fault LED on

the card with only one spray gun connected will light.

NOTE:

The unused spray gun must be the highest even-number spray

gun. For example, if there is an 8-spray gun system, then number 8 must

be the unused spray gun. The spray gun card receptacles are labeled on

the circuit boards as A (odd-number spray gun) and B (even-number spray

gun).

Included in the bag with the console keys is a bulkhead seal and jumper.

The jumper disables the spray gun not detected fault LED on the spray gun

card.

Cap the unused cable receptacle with the bulkhead seal, then open the

console door and unplug the receptacle harness from the spray gun card.

Install the jumper in the card receptacle.

Refer to the Parts section for seal and jumper part numbers.

Bulkhead

Seal

Jumper

Install in #8 Card Receptacle

Spray Gun Card

Harnesses

Receptacle #8

Figure 3-10

Seal and Jumper Installation

−

Example Showing 8-Spray Gun System Using Seven Spray Guns

Содержание Encore
































































































Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды

Nordson Encore, Установка, устранение неисправностей, ремонт

Результаты поиска

Содержание Encore

Отзывы:

Похожие инструкции для Encore

Бренды по названию

Популярные бренды