nord 6052902/0213 страница 73 Скачать руководство пользователя

Страница: 73 / 128

4 Commissioning

B 1050 en-3921

4.13.2 Optional

Checklist

Item to be checked

Date
of check:

Information
see Section

Option R, WX, FAN:

Is the direction of rotation specified and checked?

4.11, 4.6

Option D and ED:

Is the torque arm installed correctly?

3.23

Option S, FAN:

Are rotating parts covered with a contact guard?

3.14

Option FAN, CS2-X:

Is an adequate supply of air ensured?

4.6, 4.8

Option CS1-X, CC:

Is the cooling water connected to the cooling unit or the cooling
coil and open?

3.18, 3.19

Option CS1-X, CS2-X:

Is the cooling unit connected to the gear unit?

3.19

Option LC, LCX:

Is the pressure monitor connected and functioning?

4.5

Option PT100:

Is the temperature monitor connected and functioning?

4.10

Option S:

Was the shrink disc connection tested for slippage?

3.6.2

Brake option:

Is the brake correctly adjusted?

3.25

Option MT:

Is the belt correctly tensioned?

3.12

Option WX:

Has the speed monitor been functionally connected?

4.11

Table 12: Optional checklist for commissioning

Содержание 6052902/0213

































































































































Результаты поиска

Содержание 6052902/0213

Отзывы:

Похожие инструкции для 6052902/0213

Бренды по названию

Популярные бренды

nord 6052902/0213, Руководство с инструкциями по установке

Результаты поиска

Содержание 6052902/0213

Отзывы:

Похожие инструкции для 6052902/0213

Бренды по названию

Популярные бренды