nord 6052902/0213 страница 26 Скачать руководство пользователя

Страница: 26 / 128

Industrial gear units – Manual with installation instructions

B 1050 en-3921

3.1.5 Transport of agitator version gear units

The ring bolts on the motor must

not

be used for transportation.

Special lifting gear must be used to ensure correct transport if the shackle holes cannot be used due
to the IEC attachment. DIN 580 and DIN 582 ring bolts may not be used.

WARNING

Danger of injury due to the gear unit tipping or falling over

• Pay attention to the centre of gravity of the gear unit.
• Transport the motor in a position which is as vertical as possible.

Legend

1: Lifting strap

2: Shackle

: Not permissible

: Permissible

Figure 7: Transport of agitator version gear units

Содержание 6052902/0213

































































































































Результаты поиска

Содержание 6052902/0213

Отзывы:

Похожие инструкции для 6052902/0213

Бренды по названию

Популярные бренды

nord 6052902/0213, Руководство с инструкциями по установке

Результаты поиска

Содержание 6052902/0213

Отзывы:

Похожие инструкции для 6052902/0213

Бренды по названию

Популярные бренды