nord 6052902/0213 Скачать руководство пользователя страница 90 | Manualshive

Страница: 90 / 128

nord 6052902/0213 Скачать руководство пользователя страница 90

Industrial gear units – Manual with installation instructions

90

B 1050 en-3921

Figure 42: Examples of inspection covers

Checking inspection covers

1. Check fastening screws for firm fit.
2. Check sealing of the cover.

If sealings or screws are damaged or not usable, replace them. Proceed as described below.

Disassembly of the inspection cover

1. Loosen the cover.
2. Remove the cover with seal.

Make sure that no foreign bodies fall into the gear unit interior.

Assembly of the inspection cover

1.  Clean the seal surfaces on the gear unit housing and on the inspection cover.
2.  Replace screws that have become unusable with screws of the same design and strength class.
3.  Replace seals that have become unusable.
4.  Screw the cover tightly with the provided tightening torques.

(see chapter 7.4 "Screw tightening torques")

«
...
88
89
90
91
92
...
»

Содержание 6052902/0213

































































































































Отзывы:

Нет отзывов