nord 6052902/0213 Скачать руководство пользователя страница 80 | Manualshive

Страница: 80 / 128

nord 6052902/0213 Скачать руководство пользователя страница 80

Industrial gear units – Manual with installation instructions

80

B 1050 en-3921

5.2.5.6

No-seal adapter for agitators (Option: SAFOMI)

NOTICE

Damage to the gear unit due to insufficient lubricant

Oil foam formation may indicate contamination of the oil, e.g. due to the entry of foreign liquids.
Contamination impairs the lubricant properties of the gear oil and may result in damage to the gear
unit.

•  Check the gear oil for water and other contaminants.
•  Change the oil.
•  Clarify and remedy the cause of oil contamination.

With this option, the gear unit housing is equipped with a 3D oil inspection glass and an oil inspection
glass in the SAFOMI motor adapter. If the gear unit is subsequently equipped with a SAFOMI motor
adapter, the gear unit housing does not include a 3D oil inspection glass. Check the oil level with a
dipstick.

• Check the oil level in the gear unit housing with the 3D oil inspection glass. The 3D oil inspection

glass must always be completely filled with oil.

• The oil inspection glass in the SAFOMI-IEC adapter is used to check the gear oil with regard to

foam formation. No oil foam must be visible neither at a standstill nor during operation.

Figure 35: Illustration air space

Before topping up the oil, unscrew the (pressure) vent (1) or the screw plug (2) in the air space so that
air can escape from the gear unit.

Information

Incorrect oil level indication due to trapped air

During commissioning and after changing the oil, air (air pockets) may become trapped in the gear
unit oil bath. These disappear during operation. The resulting space fills with lubricant. Because of
this the oil level may deviate in comparison with the initial filling. Trapped air can escape via the gear
unit venting. This process may take several days. During this period an incorrect display of the oil
level in the 3D inspection glass cannot be ruled out.

• Check the oil level at regular intervals, especially after changing the oil or commissioning.

«
...
78
79
80
81
82
...
»

Содержание 6052902/0213

































































































































Отзывы:

Нет отзывов