nord 6052902/0213 страница 50 Скачать руководство пользователя | Manualshive

Страница: 50 / 128

background image

Industrial gear units – Manual with installation instructions

50

B 1050 en-3921

3.14 Installing the cover cap, air baffle (Option: H, H66, FAN, MF.., MS…)

NOTICE

Do not use damaged covers.

Depending on the field of use, covers are used for the following reasons:

• Personal protection (Protection from rotating machine components) (Option: H)
• Protection of gear unit components (e.g. seals) with high dust concentrations (Option: H66)

NORD fan covers and air baffles ensure a correct supply of air for the gear unit (Option FAN)

NOTICE

Risk of gear unit damage due to incorrect installation

• The fan must not make contact with the fan cover.

Information

•  Keep the fan cover and air baffle free of dust.
•  Remove dirt on the fan wheel, fan cover and protective grill with a hard brush.
•  Never use a pressure washer to clean the fan cover, baffles and protective grill.

Use all fastening screws. Secure the fastening screws by coating them with securing lubricant, e.g.
Loctite 242, Loxeal 54-03. Tighten the fastening screws with the correct torque (see chapter 7.4
"Screw tightening torques").

3.15 Fitting a standard motor (Option: IEC, NEMA)

The motor weights as well as the dimension “X max” indicated in the table below must not be
exceeded:

Maximum permitted IEC and NEMA motor weights

IEC

132

160

180

200

225

250

280

315

NEMA

210 T

250 T

280 T

324 T

326 T

365 T

Centre of gravity

X max1) [mm]

200

259

300

330

370

408

465

615

Weight [kg]

100

200

250

350

500

700

1000

1500

1)

see Figure 23 for dimension X max

Table 5: IEC and NEMA motor weights

«
...
48
49
50
51
52
...
»

Содержание 6052902/0213

































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6052902/0213

MAX-61SX-H RING WC Series

Бренд: O.S. engine Страницы: 36

TSA 200-100-220

Бренд: SCHABMULLER Страницы: 56

Бренд: Amico Страницы: 47

Бренд: Parker Страницы: 32

Бренд: ebm-papst Страницы: 9

Бренд: Kohler Страницы: 4

Бренд: Newland Страницы: 29

marine TM.5.8TS

Бренд: Toyama Страницы: 88

Бренд: Volvo Penta Страницы: 90

Бренд: Volvo Penta Страницы: 108

Бренд: Dato Страницы: 9

Бренд: Toro Страницы: 62

Бренд: Volvo Penta Страницы: 96

Бренд: Valach Страницы: 24

Бренд: YAMADA Страницы: 2

Бренд: LRP electronic Страницы: 11

Бренд: Barrus Страницы: 97

Бренд: D-MOTOR Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды