17
VPS DISASSEMBLY INSTRUCTIONS
To remove the VPS system from the helmet, open or disassemble the visor of the hel-
met and lower the VPS by pushing the slider upwards (Fig. 7B).
Hold the central part of the VPS, press it slightly towards the inner part of the helmet
and simultaneously pull the VPS downwards until its upper grip pawl has been
removed from the shell (Fig. 8).
Hold the VPS right side and pull the VPS towards the outside of the helmet by press-
ing the grip pawl in the shell housing (Fig. 9).
Repeat the same operation on the left side of the helmet.
VPS ASSEMBLY INSTRUCTIONS
To assemble the VPS, open or disassemble the helmet visor and make sure the side
slider is in upward position (Fig. 7B).
Insert the VPS left end into the left side guide until the grip pawl is hooked in shell
housing.
Repeat the same steps on the right side (Fig. 9).
Press the VPS slightly inwards near its upper grip pawl. At the same time press the
VPS in the seat obtained between the outer and inner shells (Fig. 8).
Push the VPS upwards, making sure that the side slider is moving upwards (Fig. 7B).
Check the correct VPS operation by moving the left side slider downwards (Fig. 7A)
and upwards (Fig. 7B) until you hear the clicks meaning that it is in the relevant
positions.
If necessary, repeat the above-mentioned steps.
- If the visor and/or VPS opening/closing mechanisms are damaged or malfunc-
tioning, please contact a Nolan authorised dealer.
-
Do not use the helmet if the VPS has not been assembled properly.
WARNING
-
The VPS doesn’t replace the protection guaranteed by the visor.
• WIND
PROTECTOR
This accessory allows improved helmet performance under certain conditions of use.
The Wind Protector reduces unpleasant infiltrations of air under the chin.
See Fig. 10 for the assembly and disassembly.
• REMOVABLE INNER COMFORT PADDING
1 DISASSEMBLY
1.1 Open the chin strap (see specific instructions), remove the roll-neck flap from the
cheek pad (Fig. 11), pull the front part of the left cheek pad towards the inside of
the helmet and pull out the left fastening chin strap from the slot on the cheek pad
(Fig. 12). Repeat the same operation on the right side of the helmet.
1.2 Release the roll-neck eyelet from the frame fixed to the outer shell (Fig. 13).
Содержание N43E AIR
