2.3 Insert the rear right, central and left flaps of the liner into the relevant support
seats in the helmet neck-ring area (Fig. 13). To perform this step, act as follows:
slightly deform the shell sealing edge and push the flaps until they are complete-
ly hooked to the support.
2.4 Hook the roll-neck eyelet to the frame fixed to the outer shell (Fig. 12), making
sure that the frame central hole is free.
Note: Check the correct assembly of the liner front area by lifting and lowering
the VPS. These movements should be smooth. If this is not the case, repeat the
steps 1.4 and 2.2.
2.5 Insert the left chin strap in the left cheek pad slot by pulling it towards the inside
of the helmet; then press the padding onto the snap fastener on the back of the
helmet so that it is hooked in the hooking seat of the frame fixed to the shell (Fig. 11),
put aside the roll-neck flap (Fig. 10).
WARNING!!!
- Remove the padding only when cleaning or washing is required.
- Never use the helmet if the inner comfort padding and the cheek pads have not
been correctly and completely restored.
- Delicately hand-wash in lukewarm water (max. 30°C) and neutral soap.
- Rinse off with cold water and dry up at room temperature away from direct sunrays.
- Never machine-wash the inner comfort padding.
- The inner polystyrene is an easily deformable material, in fact it is apt to change
or get partially destroyed to help absorb shocks.
- Use a wet cloth to clean it and let it dry at room temperature away from direct
sunrays.
- Do not modify the helmet's internal polystyrene components in any way.
- Never use tools or equipment of any sort to carry out the steps described above.
• SIDE PLATES
(available as standard or optional accessory for aesthetic finish of the helmet when it
is used without the visor)
1 Repeat the steps 1, 2, 3 and 4 of the visor disassembly section.
2 Lift the deformable element “D” of the visor mechanism on the left side (Fig. 15)
and remove it from the shell paying particular attention not to lose the springs of
the visor mechanism on its back.
3 Insert the teeth of the left side plate in the cavity of the visor mechanism, then
push towards the inside of the helmet near the deformable tooth “D” (Fig. 16).
4 Follow the same steps on the right side of the helmet. To assemble the visor again
first remove the side plates (see steps 2), then reassemble the visor mechanisms
(see steps 3) and the visor itself (see steps from the visor assembly section).
Note: the right visor mechanisms and side plates, identified with “ R”, are differ-
ent from the left ones, identified with “ L”.
18
Содержание N43 AIR
