in the static modes only in case of overload. When vibration is active,
the vibration icon on the INFO bar will turn green, when vibration is
disabled, it will turn red.
Vibration may not be felt in the All Metal mode with weak signals; it
will be felt as the signal gets stronger. In other words, vibration does
not start at the depth where the audio tones are heard but at a lesser
depth. Therefore, if you are detecting with vibration only and audio
tones are off, you can miss weaker and deeper signals.
Vibration speed is constant in the pinpoint mode and cannot be
adjusted. Vibration is off at 0 position. 1-5 values provide the same
level of vibration in the pinpoint mode. When vibration is used in the
pinpoint mode, vibration speed increases as the target is approached
and it reaches the maximum level over the center of the target. When
you turn off and on the device, it will start with the last vibration level
you chose.
KEYPRESS VOLUME
It is used to adjust the volume of the keypress sounds according to
your personal preference by using the plus (+) and minus (-) buttons .
It has 5 levels. As the level goes up, the volume goes up and vice versa.
At 0 level, the volume will be off and no sound will be heard when the
keys are pressed.
BRIGHTNESS
It enables you to adjust the screen backlight level according to your
personal preference. It ranges between 0-10 and it is adjusted by
the plus (+) and minus (-) buttons. At 0 level, the backlight is off. At
10, brightness will be maximum. The maximum levels of the of the
backlight will affect power consumption, so we recommend to set it
to lower levels.
KEYPAD BACKLIGHT
It enables you to adjust the backlight of the system box and handle
keypads. It has 7 levels and it is adjusted by the plus (+) and minus (-)
buttons. At 0 level, the keypad backlight is off. At 7, keypad brightness
will be maximum. The maximum levels of the of the keypad backlight will
affect power consumption, so we recommend to set it to lower levels.
LANGUAGE
It is used to change the operating language of the device. INVENIO can
be used in 17 different languages. The device will start up in the default
language set by the factory. You can change the language by selecting
this option and using the plus (+) and minus (-) buttons. Once you select
the language, just press OK and the device will switch to that language
automatically. When you turn off and on the device, it will start with the
last language you chose.
TIME/DATE
It is used to adjust the time and date. By using the plus (+) and minus
(-) buttons, select the option (hour, minute, day etc.) you want to adjust.
The selection will be marked in red. Adjust it using the up and down
buttons. Once the adjustment is done, press the OK button to save.
Once the time and date are set, you can only change them manually
again. In other words, even if you set the device to factory defaults, the
time and date will stay the same.
NOTE :
If the time and date change each time you turn off and on the
device, the clock battery may be dying. Please get in touch with your
dealer or technical service.
CM/INCH
It is used to change all the units of lengths (depth, height, width etc.)
from centimeters to inches. It is adjusted with the plus (+) and minus
(-) buttons. The selected unit will be marked in red.
OTHERS
SOFTWARE UPDATE
This option shows the software version installed on your device
and it also enables you to update your device. All software
updates for the INVENIO will be published on the product page at
www.noktadetectors.com
. You can follow all updates and instructions
from this page.
FACTORY SETTINGS
It is used to set all the options and settings of the device back to its
factory defaults.
When the factory defaults are restored, all settings except for the time,
date and language will be changed.
To restore the factory settings, press the OK button when the option
is selected. ''The system will be restored to factory defaults. Are you
sure you want to continue?'' message will appear on screen. If you
press OK, you will see the second message ''Do you also want to delete
all your saved files in the archives?''. Once you respond with yes or
no to this, the message ''Do you want to reset the neural network to
factory defaults?'' will come on screen. After you respond with yes or
no, you will see the message ''Please wait...'' and a progress bar. Once
the progress bar is full, the device will be restored to factory defaults
and will start in the Basic mode.
NOTE :
If you answer yes to ''Do you also want to delete all your saved
files in the archives?'' all 3D graphs and screenshots saved in archives
will be deleted.
NOTE :
If you answer yes to ''Do you want to reset the neural network
to factory defaults?'' the device will delete all the changes made in the
neural network.
ARCHIVES
This section of the device enables you to access all the 3D graphs
meaning result screens, the screenshots and the tutorial videos. You
can transfer all the files you saved in archives to an external USB
drive as well.
Select All
Selects all the folders or files.
Deselect All
Deselects all folders or files.
Copy Selected
Copies the selected folders or files to USB drive (except for the tutorial
videos).
Delete Selected
Deletes the selected folders or files (except for the tutorial videos).
3D FILES
All the saved 3D graphs, in other words the result screens, are collected
You can navigate between the OPTIONS with the up and down buttons.
You can change the value using the plus (+) and minus (-) buttons. If
the up/down and +/- buttons are held down, the options and values
will change rapidly. Options are shown in white. When selected, they
will turn orange. The corresponding values of an option are shown in
white, the selected one will turn red and once adjusted, it will be shown
in yellow.
NOTE :
Regardless of the screen you are in, when the OPTONS button
is pressed, the device will display the OPTIONS screen. You can go back
to the previous screen by pressing the BACK button.
FREQUENCY
It is used to change the operating frequency of the device. INVENIO
works at 14kHz only. Therefore, this option is not selectable in INVENIO
and it is active in INVENIO Pro only.
After selecting the FREQUENCY option, change the frequency using
the plus (+) and minus (-) buttons. You will hear the sound of the relay
circuit in the shaft; this is normal.
INVENIO offers 3 operating frequencies — 5kHz, 14kHz and 20kHz— to
suit different target and soil types. Based on the frequency selected,
the detector's detection performance for different types of targets will
vary. The list below includes, but are not limited to, different types of
targets that correspond to each frequency :
5kHz :
Large ferrous and non-ferrous objects - High conductives (silver,
copper etc.) - Medium or relatively small targets in non-mineralized
ground without iron trash - Ferrous masses and militaria.
14kHz :
General use - Different size targets in medium-highly
mineralized ground.
20kHz :
Small coins and large objects with different conductivities as
well as thin large coins - Gold coins, rings, small jewelry, sheet iron,
foil - Small targets in iron trash.
IMPORTANT!
Please remember to re-ground balance upon changing
the frequency.
FREQUENCY SHIFT
It allows you to shift the frequency in small steps. It is used to eliminate
the electromagnetic interference that the device receives from another
detector which operates in the same frequency range nearby or from
the surroundings. If too much noise is received when the search coil is
lifted in the air, this may be caused by the local electromagnetic signals
or excessive sensitivity settings.
To eliminate the noise caused by electromagnetic interference, try
shifting the frequency first before lowering the sensitivity to obtain
maximum depth performance. Frequency shift consists of 5 steps (-2
/ -1 / 0 / +1 / +2). Default setting is 0 which is the central frequency.
IMPORTANT!
Frequency shift may impair performance. Therefore, it is
suggested that you do not shift the frequency unless it is necessary. In
cases where the interference cannot be eliminated with the frequency
shift, in the INVENIO Pro, the operating frequency of the device (5kHz /
14kHz / 20kHz) may also be changed.
IPTU SENSOR
Allows you to turn on and off the IPTU sensor and switch between 2
detection screens - one with and one without the sensor. The device
will start in detection screen with the IPTU sensor at initial start up. If
you wish, you can turn the IPTU sensor off by using this option and
switch to the detection screen without the IPTU sensor.
WIRELESS HEADPHONE CHANNEL
It is used to change the channel of the optional wireless headphones.
It consists of 5 channels and an off position. When it is at off, there will
be no wireless connection available for the headphones.
You scan the channels manually or automatically. To scan manually,
use the plus (+) and minus (-) buttons when the option is selected. Each
time you press the + or the - button, you need to wait approximately 1
second. If you want to scan the channels automatically, press the OK
button when the option is selected. Channels will be scanned one by
one and an automatic connection will be attempted. If you wish, you
can cancel the auto scan by pressing the OK button. If no connection
is made after each channel is auto scanned, the scanning will be
terminated.
WIRELESS SHAFT CHANNEL
It is used to change the wireless connection channel of the shaft &
handle. It consists of 32 channels and an off position. When it is at
off, there will be no wireless connection available between the system
box and the shaft & handle. To scan the channels manually, you can
use the plus (+) and minus (-) buttons. Each time you press the + or
the - button, you need to wait approximately 1 second. If you want to
scan the channels automatically, press the OK button when the option
is selected. Channels will be scanned one by one and an automatic
connection will be attempted. If you wish, you can cancel the auto scan
by pressing the OK button. If no connection is made after each channel
is auto scanned, the scanning will be terminated.
VOLUME
This control allows you to increase or decrease the device's volume
based on your preference and environmental conditions. Volume level
can be adjusted from 0 to 10 using the plus (+) and minus (-) buttons.
When the volume is turned off completely, the volume icon on the
INFO bar will turn red. When you turn the volume up, it will turn
green. In addition, while the device is in detection screen, volume can
be adjusted with the plus (+) and minus (-) buttons directly, without
going into OPTIONS. When you turn off and on the device, it will start
with the last volume level you chose. Because the volume level affects
power consumption, we recommend you not to increase it more than
necessary.
VIBRATION
This option is used to adjust the vibration level.
This feature provides feedback to the user by producing a vibration
effect when a target is detected. It can be used independently or
together with the audio response. When audio response is disabled,
all feedbacks are provided to the user as vibration only during target
detection.
Vibration has 5 levels and it is adjusted with the plus (+) and minus (-)
buttons. When it is set to 0, vibration feature is completely disabled. If
the vibration is set to the 1st level, the device provides long vibration
signals and at 5 it provides short vibration signals. The magnitude of
the vibration effect can vary according to the depth of the target and
the swinging speed. Vibration works in motion modes only. It works
15
OPTIONS/MOŽNOSTI
3D FILES/3D SÚBORY
V tomto priečinku sa ukladajú všetky uložené obrazovky výsledkov. Sú
usporiadané v chronologickom poradí. Grafy uložené v rovnaký deň sú
očíslované a uložené v rovnakom priečinku. Grafy uložené v rôznych
dátumoch sa uložia a zoradia podľa dátumu uloženia. V zobrazení
priečinka vedľa ikony priečinka môžete vidieť dátum a počet záznamov v
priečinku.
Na výber priečinka stlačte tlačidlo plus (+). Pole výberu sa presunie do
susednej sekcie. Zvolený priečinok sa zobrazí oranžovou farbou. Ak je
uložených viacero priečinkov, pomocou tlačidiel nahor a nadol sa v nich
môžete pohybovať a pristupovať k nim stlačením tlačidla OK. Keď už ste v
priečinku, môžete záznam vybrať pomocou smerových tlačidiel a otvoriť
ho stlačením tlačidla OK. Keď chcete skončiť, stačí stlačiť tlačidlo SPÄŤ.
Celkovo sa na jednej stránke zobrazí 6 priečinkov a 6 3D grafov v
každom priečinku. Keď sa počet obrazoviek výsledkov a priečinkov
zvýši, zariadenie automaticky pridá ďalšie strany. Čísla strán sa
zobrazia v spodnej časti obrazovky. Stlačením tlačidla nadol môžete
prejsť na výber stránky a vybrať požadovanú stránku pomocou
tlačidiel plus (+) a mínus (-). Priečinky sa zobrazujú v chronologickom
poradí od najnovšieho po najstarší.
SCREENSHOTS/SNÍMKY OBRAZOVKY
V tejto sekcii sú uložené všetky vyhotovené snímky obrazovky.
Po výbere snímok obrazovky vyberte priečinok stlačením tlačidla plus
(+). Pole výberu sa presunie do susednej sekcie. Zvolený priečinok sa
zobrazí oranžovou farbou. Ak je uložených viacero priečinkov, pomocou
tlačidiel nahor a nadol sa v nich môžete pohybovať a pristupovať k
nim stlačením tlačidla OK. Keď už ste v priečinku, môžete záznam
vybrať pomocou smerových tlačidiel a otvoriť ho stlačením tlačidla OK.
Keď chcete skončiť, stačí stlačiť tlačidlo SPÄŤ.
Keď je na obrazovke zobrazený obrázok, ak stlačíte tlačidlo
SETTINGS/NASTAVENIA, v hornej časti sa zobrazí správa DELETE.
Ak stlačíte tlačidlo OK, zobrazí sa správa ''Are you sure you want
to delete the selected items?'' (Naozaj chcete vymazať vybraté
položky?). Stlačením OK vymažete a prejdete na ďalší záznam.
Celkovo sa na jednej stránke zobrazí 6 priečinkov a 6 snímok
obrazovky v každom priečinku. So zvyšujúcim sa počtom snímok
obrazovky a priečinkov bude zariadenie automaticky pridávať ďalšie
stránky. Čísla strán sa zobrazia v spodnej časti obrazovky. Stlačením
tlačidla nadol môžete prejsť na výber stránky a vybrať požadovanú
stránku pomocou tlačidiel plus (+) a mínus (-). Priečinky sa zobrazujú v
chronologickom poradí od najnovšieho po najstarší.
TUTURIAL VIDEOS
/INŠTRUKTÁŽNE VIDEÁ
V tejto sekcii nájdete inštruktážne videá zoskupené pod rôznymi
názvami. Vyberte požadovaný priečinok a stlačte tlačidlo OK.
Zobrazia sa všetky videá v priečinku. Pomocou smerových tlačidiel
vyberte video, ktoré chcete sledovať, a stlačte tlačidlo OK.
Po otvorení videa budú tlačidlá fungovať nasledovne:
Tlačidlá p
lus (+) a minus (-) :
Ovládanie hlasitosti.
Tlačidlá hore a dole:
Umožňujú vám prechádzať medzi videami a počas
prehrávania ich pretáčať dopredu a dozadu.
Tlačidlo
OK:
Spustí a zastaví video.
Tlačidlo
BACK
/SPÄŤ
:
Zatvorenie videa a návrat do zoznamu.
DELETING THE ARCHIVES FILES AND SAVING
You can delete multiple or individual files in the archives or save them
to a USB drive (except for the tutorial videos).
To delete individual files :
Using the plus button (+), select the small box next to the file or folder.
The box will turn orange. When you press the OK button, a check mark
will appear in the box and the line will appear blurred. Click the trashcan
icon next to the box and press OK. The warning message ''Are you sure
you want to delete the selected items?'' will appear on screen. Press OK
to confirm.
NOTE :
When you want to delete multiple files, you can check the boxes
next to the files and use ''Delete Selected'' function at the top.
To delete multiple files :
To delete multiple files or folders in the archives, when the file or the
folder is selected, go to ''Select All'' using the up button (it will turn
orange). Then press OK. All small boxes will be checked and all the
lines will appear blurred. Then select ''Delete Selected'' at the top and
press OK. The warning message ''Are you sure you want to delete the
selected items?'' will appear on screen. Press OK to confirm.
EXTERNAL USB MEMORY USAGE
You can copy the 3D graphs and screenshots to a USB drive and view
them from the USB drive as well. When you insert the USB drive to the
device, the USB icon in the archives screen will appear in white. Select
the USB icon using the plus (+) button. The icon will turn orange and the
folders inside will be listed.
When a USB drive is inserted in the device, the USB icon will show in
the archives screen and on the INFO bar. Once you exit the archives, the
USB icon will no longer show on the INFO bar even if the USB drive is
still attached. If you open the archives screen again, the USB icon will
come back after a short period of time.
IMPORTANT!
Do not remove the USB drive while in the archives
screen! Be sure to exit the archives screen before you remove the
USB memory.
Saving to External USB Memory
Using the plus button (+), select the small box next to the file or folder.
The box will turn orange. When you press the OK button, a check mark
will appear in the box and the line will appear blurred. Click the USB
icon next to the box and press OK. The warning message ''Are you sure
you want to save the selected items to an external memory device??''
will appear on screen. Press OK to confirm.
NOTE :
When you want to save multiple files, you can check the boxes
next to the files and use ''Save Selected'' function at the top.
To save multiple files or folders in the archives, while the file or the
folder is selected, go to ''Select All'' using the up button (it will turn
orange). Then press OK. All small boxes will be checked and all the
lines will appear blurred. Then select ''Copy Selected'' at the top and
press OK. The warning message ''Are you sure you want to save the
selected items to an external memory device??'' will appear on screen.
Press OK to confirm.
NOTE :
If you want to cancel any of the operations while the warning
messages are displayed on screen, press the BACK button.
NOTE :
If there is no USB drive inserted during the save process, the
message ''No external memory device is available!'' will appear.
NOTE :
You can view the result screens and the screenshots saved on
the USB drive on a computer in picture format.
