background image

Nokia M11 User’s Manual

 

E

 Copyright Nokia Networks Oy

C33833001SE_00

Glossary-4

bridge

A device that connects two or more physical networks and forwards
packets between them. Bridges can usually be made to filter packets,
that is, to forward only certain traffic.

broadcast

A packet delivery system where a copy of a given packet is given to all
hosts attached to the network.

brouter

A device which is both a bridge and a router.

command line interface

Character-based user interface where a command line ending with
<CR> character is used to configure a device. The device interprets the
command and returns a character-based response.

Config command hierarchy

A hierarchy of nodes which contain the configurable parameters of
M11. It is used to configure M11 through the command line interface.
See Root command hierarchy.

Digital Subscriber Line Access Multiplexer

A network element which multiplexes the traffic coming from the
high-speed subscriber lines and forwards this traffic to the ATM
network.

domain name service

Domain name service (DNS) is used for translating names of network
nodes into addresses.

Содержание M11 T66220










































































































































































Отзывы: