Nice MhouseKit SL1W, Инструкции и предупреждения по установке и использованию

Страница: 31 / 156

English – 29
English
LED P1 Status Action
Off Anomaly or control unit in full standby mode Automation could be in standby; press and release a key to see
if the led lights up or flashes; if this has no effect make sure there
is power supply; check that the fuses are not blown; if this is the
case, verify the cause of the fault and then replace them with oth-
ers of the same value
1 fast red flash each second The control unit has no memorised wireless
devices configuration (factory condition)
Normal operation; the control unit does not have any wireless de-
vice installed and is ready to learn a wireless network.
1 fast green flash each sec-
ond
Automation moving or in test:
The control unit has at least one accessory
device installed.
Normal operation
2 fast green f pause
for 1 second
The automation is neither moving nor in test.
The control unit has at least one accessory
device installed; the last manoeuvre was
successful and all devices respond correctly
and have their batteries charged.
Normal operation
1 fast red flash followed by 1
fast green flash + 1 second
pause
The automation is neither moving nor in test.
The control unit has at least one accessory
device installed; the last manoeuvre was
successful and all devices respond correctly
but at least one has an almost empty
battery .
Check the battery charge level on the wireless devices; activate the
test procedure (paragraph 8.2 )
1 fast green flash followed by
1 fast red flash + 1 second
pause
The automation is neither moving nor in
test. The control unit has at least one ac-
cessory device installed; the last manoeuvre
was successful and all devices respond cor-
rectly, but the control unit did not receive
a good radio signal from at least one of
them .
Limited radio communication; if possible, search for a better posi-
tion for the device
2 fast red f pause for
1 second
The automation is neither moving nor in test.
The control unit has at least one accessory
device installed; the last manoeuvre was
successful and all devices respond
but at
least one of them has an almost com-
pletely empty battery and at least one
did not send a good radio signal to the
control unit
.
Check the battery charge level on the wireless devices; activate the
test procedure (paragraph 8.2 ).
Limited radio communication; if possible, search for a better posi-
tion for the device
Red LED on The automation is neither moving nor in test.
The control unit has at least one accessory
device installed; the last manoeuvre was
successful but at least one device on the
network did not respond .
Check the battery charge level on the wireless devices; activate the
test procedure (paragraph 8.2 ).
Limited radio communication; if possible, search for a better posi-
tion for the device
Red LED on The automation is moving or in test. The
control unit has at least one pair of photo-
cells installed.
Normal operation if there is an obstacle between at least one pair
of photocells, or at least one photocell is not responding. Check
the battery charge level on the wireless devices; activate the test
procedure (paragraph 8.2 ). It is possible that radio communication
is at its limit; if possible, search for a better position for the device.
There may also be a radio interference problem.
1 red coloured short flash
every 0.5 seconds
Network learning procedure by new control
unit (cloning) in progress; the control unit is
waiting for the address of the old network
Normal operation
1 green coloured short flash
every 0.5 seconds
The control unit is detecting the old devices Normal operation
1 red+green coloured short
flash every 0.5 seconds
Network learning procedure by new (clon-
ing) in course; the control unit has received
the address of the old network
Normal operation
LED P2 Status Action
Off All OK No memorisation in progress.
On Memorisation in Mode 1 During memorisation in mode 1, it is normal for it to take a maxi-
mum of 10 s.
Series of quick flashes, from
1 to 4
Memorisation in Mode 2 During memorisation in mode 2, it is normal for it to take a maxi-
mum of 10 s.
5 quick flashes Cancellation OK Completion of deletion of a transmitter.
1 slow flash Wrong command A command has been received from an unmemorised transmitter
3 slow flashes Memorisation OK Memorisation completed successfully
5 slow flashes Cancellation OK Completion of deletion of all transmitters.