GD00BLE-1
EXCLUSIVELY
FOR WALMART
©
GARAGE DOOR
OPENER
REMOTE COMMAND
TRANSCEIVER
with TILT SENSOR
Installation Instructions
1
PRODUCT DESCRIPTION
2
SAFETY NOTES
3
PRODUCT COMPONENTS
4
TILT SENSOR INSTALLATION AND BATTERY
5
PAIRING TILT SENSOR & RESETTING TO FACTORY DEFAULTS
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,GD00BLE-1 - P/N: 10026532 X8 - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 11.000” X 8.500” - TOL. +/-.125" - SCALE: 1-1 - FOLDING: 2-FOLD ALTERNATE - SIDE 1 OF 2
GD00BLE-1
POWER
INPUT
JACK
WARNING
LIGHT
LINK
BUTTON
CONNECTION
WIRES
MOUNTING SCREWS
AND ANCHORS
FOR GD00BLE-1
POWER
SUPPLY
TILT
SENSOR
STATUS
INDICATOR
OPTIONAL
ADJUSTABLE
GD00BLE-1 MOUNTING
BRACKET
SCREWS AND
MOUNTING TAPE
FOR TILT SENSOR
WIRE
TIES
SCREW AND
MOUNTING HARDWARE
FOR ADJUSTABLE
BRACKET
WALL
OUTLET
POWER
SUPPLY
POWER
INPUT
JACK
LINK
BUTTON
GD00BLE-1
CR2032
PLUS SIDE UP !!!
The system will notify you
when the battery is low,
replace the battery with
a type CR2032 coin cell
Insert the
battery
into the
transmitter
To open the case, twist
a small screwdriver
in case slot
SLOT
Use double sided tape or
the two mounting screws supplied
(drill 1/16" pilot holes if required)
POST ON
BOTTOM
"UP"
ARROWS
Snap the sensor onto
the mounting plate
To activate the tilt sensor,
remove the battery protection pull strip
2
ARROWS ON PLATE
& SENSOR POINT UP
LOW BATTERY REPLACEMENT
1
2
1
3
Attach the mounting plate
to the
top panel of the door
GD00BLE-1 Summary of Operation
• GD00BLE-1 connects to the garage
door opener’s pushbutton wall console
terminals.
• A wireless tilt sensor mounts on garage
door and reports door’s position to
GD00BLE-1.
• GD00BLE-1 uses BLE for communication
to open or close the garage.
• A warning indicator light flashes and a
beeper sounds for 5 seconds before the
door begins to move.
• If the door does not completely open or
close, a second open or close command
can be sent after 30 seconds.
• If the door does not completely open
or close after the second attempt, the
GD00BLE-1 operation is suspended until a
local garage door pushbutton is activated.
WARNING
This operator system is equipped with an unattended
operation feature. This door could move unexpectedly. NO
ONE SHOULD CROSS THE PATH OF A MOVING DOOR!
WARNING
The Remote Command Transceiver must be mounted in the
garage, in sight of the garage door, where the visual and audible
movement warning indicators can be clearly seen and heard.
WARNING
Do not install the Remote Command Transceiver on garage
door operators manufactured prior to 1993 (models without
an operational safety beam entrapment detection system).
WARNING
This system can be installed on sectional type doors only per
(UL-325). DO NOT INSTALL ON ONE-PIECE DOORS!
The GD00BLE has already been set to factory defaults and pre-paired with the
tilt sensor. NO RESET OR PAIRING IS REQUIRED. The following instructions are
provided for reference only
• Quickly pressing the LINK button 5 times will reset the GD00BLE to the factory
defaults (Tilt pairing will be preserved).
• Long pressing with LINK button (3-5 seconds) until an audible beep is heard will
re-pair/learn the Tilt Sensor.
Please download the Walmart
©
InHome
app from the Apple or Android PlayStore.
Reserved for Bluetooth QR Code
Reserved for HomeKit QR Code and label
Available if needed
Reserved for
Walmart URL pointer
on-boarding text and
QR Code
