Nice MhouseKit SL1W, Инструкции и предупреждения по установке и использованию

Страница: 18 / 156

16 – English
English
PROGRAMMING
––– STEP 7 –––
7.1 - PRELIMINARY CHECKS
As soon as the control unit is electrically powered, you are advised to
carry out some simple tests:
01. Check that the LED “C” on the control unit ( fig. 36 ) is flashing stead-
ily, at a speed of around one flash per second.
02. Check that the night light on keyswitch KS100 is on.
03.
If the above conditions are not satisfied, it is advisable to switch off
the power supply to the control unit and check the electrical connec-
tions more carefully. For other useful information see also chapters
10.5 “Troubleshooting” and 10.6 “Diagnostics and signals”.
7.2 - RECOGNITION OF THE DEVICES
WARNINGS:
• To locate the leds and keys mentioned in this manual on the PH100W
and FL100W devices, see fig. 37 .
• For procedures requiring battery insertion (or removal) in the various
devices, see fig. 40 for PH100W and fig. 41 for FL100W.
• All programming phases end automatically, 2 minutes following the last
action. Any changes made up to that point are stored in any case.
This procedure makes it possible to recognise wireless devices with the
Power&Free System and those connected to the STOP input.
IMPORTANT!
- During installation, the wireless devices must have mem-
ories which contain no data whatsoever, as per factory setting.
01. Press and hold P1 on the control unit and release it once the P1 led
is lit with a solid green light: now, the unit is ready to acquire wireless
devices.
02. Insert the batteries into the wireless device ( fig. 40 for PH100W and
fig. 41
for FL100W) or, if the batteries are already inserted, press and
release “
T
” on the device (
fig. 37
): the control unit will emit a brief
sound (beep) to confirm acquisition and on the device, the led “A”
(
fig. 37
) will begin to flash green and the led “B” (
fig. 37
) will begin to
flash, until the procedure is complete.
35
A
6.4 - POWER SUPPLY CONNECTION
WARNINGS!
– The PVC power cable is suitable for indoor installations. For
installation outdoors, you must protect the entire cable with a pro-
tective duct. Alternatively, you can replace the cable with one of
type H07RN-F.
– The final connection of the automation to the electrical mains or
substitution of the cable supplied must be performed exclusively
by a qualified and expert electrician, in compliance with local safe-
ty standards and the following instructions.
• For operational and programming tests of the automation
, use
the cable supplied, inserting the plug into an electrical socket. If the sock-
et is far from the automation, use a suitable extension lead.
• For the test and commissioning phase of the automation you
must connect the control unit permanently to the mains power supply,
replacing the supplied cable with another of suitable length. To make the
connection between the cable and the gearmotor control unit, proceed as
described below:
WARNING:
Provide a device inside the electricity supply line that ensures complete
disconnection of the automation mechanism from the grid. The dis-
connection device must have contacts with an opening distance large
enough to permit complete disconnection under the conditions sanc-
tioned by overvoltage category III, in accordance with installation regula-
tions. The device ensures quick, safe disconnection from the power sup-
ply if needed, and must therefore be positioned in view of the automation
mechanism. If, on the other hand, it is located in a position which is not
visible, there must be a system for preventing accidental or unauthorized
reconnection with the power grid to prevent this risk. The disconnection
device is not supplied with the product.
01. Make sure that the gearmotor plug is not plugged into the wall sock-
et;
02. Disconnect the power supply terminal electrical cable from the gear-
motor;
03. Slacken off the collar [A] ( fig. 35 ) under the clamp and pull out the
wire. Replace it with a permanent power supply cable;
04. Connect the electric cable to the gearmotor power supply terminal
(
fig.
35);
05. Tighten the collar [A] ( fig. 35 ) to secure the electric cable.
TABLE 8 - Device operating modes
A
= Flashing indicator (timings set by con-
trol unit)
B
= Courtesy light (lit during the manoeu-
vre and for an additional 15 seconds)
C
=
Courtesy light
(lit during the manoeu-
vre and for an additional 30 seconds)
D
= Courtesy light (lit during the manoeu-
vre and for an additional 45 seconds)
E
= Courtesy light (lit during the manoeu-
vre and for an additional 60 seconds)
F
= Courtesy light (lit during the manoeu-
vre and for an additional 75 seconds)
G
= Courtesy light (lit during the manoeu-
vre and for an additional 90 seconds)
Note : • During operation the courtesy light will light up only when the device
detects ambient twilight or total darkness. • To test that the courtesy light lights
up during the day, cover the cell with something opaque, to simulate darkness.