background image

4 - SETTING OPERATING MODE

Default: 1 motor, manual

This procedure is used to set the number of motors connected and the type of control.

There can be 1 or 2 motors (synchronised operation).

Operation via radio can be:

MANUAL the motor moves in the direction selected until the transmitter key is held down  

NOTE: sensors not enabled

AUTOMATIC each time the key is pressed the motor moves 30% of the total travel in the selected direction 

VENETIAN press and release the key and the motor moves slightly in the selected direction, press and hold (>2sec) and 

it moves fully in the selected direction

OPEN/STOP/CLOSE each time the key is pressed the motor moves fully in the selected direction

Note: 

if automatic, Venetian or OPEN/STOP/CLOSE operation is set it will be necessary to notify the control unit of the 

working time of the motor(s) with the procedure in paragraph 6 every time that the parameter is changed

PROCEDURE

STEP 1 

Keep pressing and releasing the SEL key until the 

«Mot. Type» LED comes on.

The display shows the current setting.

STEP 2 

Press and release the SET button to confirm. The LED on 

the display flashes.

STEP 4 

Press and release the SET button to confirm.

Wait 20 seconds or press the SEL button until  

a horizontal line appears on the display.

Note: 

if automatic or Venetian operation is set it will be necessary to notify the control unit of the 

working time of the motor(s) with the procedure in paragraph 6 every time that the parameter is 

changed

STEP 3 

By pressing and releasing the SEL key, select the value 

corresponding to the setting you want, according to the 

following table.

DISPLAY NO.

DESCRIPTION

1

1 motor manual operation

2

1 motor automatic operation

3

1 motor Venetian operation

4

1 motor Open/Stop/Close operation

5

2 motors manual operation

6

2 motors automatic operation

7

2 motors Venetian operation

8

2 motors Open/Stop/Close operation

E

Exit

6

SOLE

NEVE

TEMP.

PIOGGIA

VENTO

T.MOT.

CODE

MOT.TYPE

SEL

Sens.

Rit. Neve

SET

SOLE

NEVE

TEMP.

PIOGGIA

VENTO

T.MOT.

CODE

MOT.TYPE

SEL

Sens.

Rit. Neve

SET

SOLE

NEVE

TEMP.

PIOGGIA

VENTO

T.MOT.

CODE

MOT.TYPE

SEL

Sens.

Rit. Neve

SET

SOLE

NEVE

TEMP.

PIOGGIA

VENTO

T.MOT.

CODE

MOT.TYPE

SEL

Sens.

Rit. Neve

SET

Содержание PRG-M24

















Отзывы: