Newmac BC 160, Инструкция по установке, эксплуатации и обслуживанию

Страница: 11 / 50

10
Runaway Fire
This can be caused by too high a flue draft or excessive fuelling.
(1)
Close all sources of air to the boiler. Be sure draft fan is turned off.
(2) Set the barometric draft regulator wide open to reduce draft.
PREPARATION OF WOOD
ONCE I HAVE MY WOOD AT HOME, HOW DO I PREPARE IT FOR BURNING?
The wood must be cut to length to suit the firebox of the stove, furnace, or fireplace in which it is to be
burned. An 8’ log may be cut into four, six or eight pieces, depending on the desired length. Splitting the
wood greatly facilitates drying and reduces the wood to a more manageable size.
HOW MUCH MOISTURE IS CONTAINED IN WOOD?
Many softwoods have a moisture content in the vicinity of 55 per cent when they are freshly cut. The
popular hardwoods have moisture contents of about 45 per cent. Air-dried wood has a moisture content
of about 15 per cent and kiln-dried wood may have a moisture content of less than 10 per cent when it is
fresh from the kiln.
WHAT CAUSES WOOD TO ROT?
When wood is cut, it is very susceptible to the growth of fungi, which converts the wood to water, carbon
dioxide, and heat, just as a fire does. This rotting decreases the wood’s energy. The fungi are most
productive when three conditions are met; the temperature is between 60 ºF and 90 ºF, the wood’s
moisture content is above 30 per cent, and ample oxygen is available.
Thus, wood does not rot
appreciably when it is dry, in the winter, or when it is submerged in the water, but it should not be allowed
to lie on the ground during the summer.
HOW CAN THIS ROTTING BE PREVENTED?
When the wood has been cut into stove wood lengths, and split, it should be piled outside during the
months of June, July and August. Two poles should be placed on the ground to serve as rails to keep the
firewood off the moist ground and the wood should be piled up in such a way that it is well exposed to the
sun and the wind. The moisture content of the wood will drop until it reaches equilibrium with the ambient
weather conditions. When the relative humidity is 60 per cent, the equilibrium moisture content is about
11 per cent. When the wood has reached this equilibrium moisture content, it is said to be “air-dried.”
Around mid-August, it should be placed under cover so that it will not reabsorb moisture from the rain and
snow before it is used.
WHY THIS CONCERN ABOUT ALLOWING THE WOOD TO DRY?
Green or wet wood is undesirable for several reasons. Green or wet wood tends to mildew and rot which
causes a significant reduction of the thermal value. When green or wet wood is burned, it may take 20 to
25 per cent of the thermal value of the wood heat to evaporate and drive off the moisture that is
contained. Green wood does not burn easily and, in order to keep the fire burning, it is often necessary to
add a lot of fuel and provide excessive draft, thereby decreasing the efficiency of the unit. The excess air
needed for combustion must be heated and it escapes up the chimney wasting heat that should be used
to heat the house.
WHAT IS CREOSOTE?
Wood smoke almost always contains some unburned gases and a fog of unburned tar-like liquids. Some
of these materials will condense on the inside of the chimney, just as the steam condenses on any cold
surface. This condensation is a black, tacky, fluid when first formed. When it dries, it is flaky and shiny.
Creosote has approximately the same thermal value as fuel oil. Not only does it reduce the effective size
of the chimney, but an accumulation of this material constitutes a serious fire hazard.
DOES GREEN WOOD CAUSE CREOSOTE?
Yes. Indirectly, green wood does cause creosote. The exhaust gases cool as they rise up the chimney.
If the temperature falls below the dew point, any moisture contained in these gases will condense on the
inside of the chimney, absorb the various products of incomplete combustion and form creosote. When
green wood is burned, the exhaust gases carry a high moisture content in addition, because of the heat