Newland HR3260-CS Скачать руководство пользователя страница 41

Страница: 41 / 165

【

Enter Setup

】

【

Exit Setup

】

Timeout between Decodes (Same Barcode)

Timeout between Decodes (Same Barcode) can avoid undesired rereading of same barcode in a given

period of time.

To enable/disable the Timeout between Decodes (Same Barcode), scan the appropriate barcode below.

Enable Timeout between Decodes:

Do not allow the scanner to re-read same barcode before the

timeout between decodes (same barcode) expires.

Disable Timeout between Decodes:

Allow the scanner to re-read same barcode.

【

Disable Timeout between Decodes

】

【

Enable Timeout between Decodes

】

The following parameter sets the timeout between decodes for same barcode. It is programmable in 1ms

increments from 0ms to 65,535ms. The default setting is 1,500ms.

Set the Timeout between Decodes (Same Barcode) to 2,500ms:

1. Scan the

Enter Setup

barcode.

2. Scan the

Timeout between Decodes (Same Barcode)

barcode.

Scan the numeric barcodes “2”, “5”, “0” and “0”. (See the

Digit Barcodes

Appendix

)

4. Scan the

Save

barcode. (See the

Save/Cancel Barcodes

Appendix

)

5. Scan the

Exit Setup

barcode.

【

Timeout between Decodes (Same Barcode)

】

Содержание HR3260-CS






































































































































































Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды

Newland HR3260-CS, Руководство пользователя

Результаты поиска

Содержание HR3260-CS

Отзывы:

Похожие инструкции для HR3260-CS

Бренды по названию

Популярные бренды